Operating Instructions; Padlocking; Safety Testing Approvals; Fluid Compatibility - Tuthill Fill-Rite FR300V Serie Manual De Instalación Y Operación

Operating Instructions

1. Reset Meter to "0" (if applicable).
2. Remove dispensing nozzle from nozzle boot.
3. Move the switch lever to the "ON" position to power the pump.
4. Insert the dispensing nozzle into the container to be filled.
5. Operate the nozzle to dispense fluid; release nozzle when the desired amount
of fluid has been dispensed.
6. Move switch lever to the "OFF" position to stop the pump.
7. Remove the dispensing nozzle from the container and store it in the nozzle boot.
CAUTION! Always keep the nozzle in contact with the container being filled during the filling process to minimize the possibility of static electricity build up.

Safety Testing Approvals

The Fill-Rite FR300V pumps have been safety tested for compliance to the standards set forth by UL Laboratories.

Fluid Compatibility

Diesel fuel, gasoline, kerosene, mineral spirits, Stoddard solvents, heptane, bio-diesel (B20 max.), and bio-diesel (B21 – B100) using KIT300BD.
IMPORTANT! If in doubt about compatibility of a specific fluid, contact supplier of fluid to check for any adverse reactions to the following wetted materials: cast
iron; steel; zinc plated steel; 300 series stainless steel; carbon; polyester; fluorocarbon; Teflon; brass; iron; copper; buna; 400 series stainless steel; aluminum.

Technical Information / Specifications

Design Features:
• Inlet: Bung: 2" male NPT; Suction pipe: 1-1/4" female NPT or
for "E" series models Bung: 2" male BSPT; Suction pipe: 1-1/2" BSPP.
• Outlet: 1" NPT, or 1" BSPT (BSPT on "E" series models).
• Cast iron pump housing: iron (composite) rotor, and carbon (composite) vanes.
• Security: Pump equipped for padlocking (see page 7 for details).
• Thermal overload protection.
• Heavy duty switch.
• 30 minute duty cycle.
• Explosion proof motor UL listed with sealed bearings that require no maintenance.
• Integral check valve with pressure relief on inlet side prevents pressure build up
and improves vertical lift.
• Easy access strainer.
• Automatic bypass valve.
• 2" threaded base for tank openings.
• Constant Amp Draw (Service Factor of 1.0):
- 115V AC 60Hz – 9.8 amps / 50Hz - 11.4 amps.
- 230V AC 60Hz – 4.9 amps / 50Hz - 5.7 amps.
Overall Dimensions:
• Model FR310V: 17.12" wide X 15" high x 14.9" deep.
• Model FR311V: 17.12" wide X 19.25" high x 14.9" deep.
• Model FR319V: 17.12" wide x 19.4" high x 14.9" deep.
INSTALLATION AND OPERATION MANUAL

Padlocking

Your Fill-Rite pump nozzle can be padlocked
for added security. With the pump turned off,
and the nozzle in the stored position, a padlock
can be inserted through the nozzle rest and
nozzle handle opening. This configuration
prevents the nozzle from being removed
from the nozzle cover.
Shipping Weight:
FR310V: 80 lbs. / FR311V: 91 lbs. / FR319V: 92 lbs.
Accessories:
See page 9 for a complete list of available accessories.
Performance:
• 26 psi (1.79 bar) maximum pressure at pump outlet.
• Up to 35 gallons (132 liters) per minute.
• Maximum viscosity of fluid pumped: #2 diesel fuel.
• Maximum Pump Operating Temperature: 150 degrees F (66 degrees C).
• Minimum Pump Operating Temperature: minus 13 degrees F (minus 25 degrees C)
(note that for operation at lower temperatures, we recommend the "Arctic Nozzle"
and "Arctic Hose" accessories section on page 9).
Suction Lift:
The lift in feet is equal to the vertical distance from the surface of the fluid in the tank
to the inlet of the pump, LESS friction losses through the vertical and horizontal runs of
pipe, all elbows, and other fittings. System should be set up to require a minimum amount
of suction lift.
• For gasoline use models FR300VN and FR303V (1/2 hp models), suction lift cannot
exceed 10' (3 m).
• For #2 diesel fuel use all other models (3/4 hp), suction lift is 18' (5.5 m).
fillrite.com | tuthill.com
7