Program Mode - General Rules For Navigation In The Software; Basic Navigation - Hedson IRT COMBI 4-1 IR/UVA Manual De Operación

7. Program mode - General rules for navigation in the software

The display shows software defined options in the bottom corner fields. To adjust the values use the arrow keys. To move to previous display
without saving, press cancel.

7.1 Basic navigation

There are 12 predefined programs for IR and 3 for UV. All 15 programs have editable names and drying parameters. Scroll up or down using the
arrow keys, press select to run the program or view to edit.
1
2
3
4
5
7.2 Run
7.2.1
The distance to the object within the circular
laser pattern is indicated on the display.
Adjust to the desired distance (IR: 60 cm,
UVA: 35-50 cm). If measuring fails "check
distance manually" appears. Use the buttons
Stop or cancel
on the keyboard to alter between one or two
returns to 7.1.
active cassettes and to turn on/off the temp.
control. See chapter 8.1.
7.2.2
Press start to begin the drying sequence.
The remaining time of the "flash off" will start
counting down. When the count down is
finished, the program automatically changes
to full bake mode.
7.2.3
programs)
This graph is available when the temperature
control is active. The graph describes the
target, actual temperature, and remaining
time. See chapter 8.1.
7.2.4
These are the same values as shown in
program graph (7.2.3), except for the
remaining time, but also the used power
capacity of the machine and the energy
consumption of the current drying process.
Note! An inactive temperature control does
not show temperature values.
7.2.5
Total energy consumption per drying process
is shown for the last 10 runs.
7.2.6
When flash off and full bake times have
expired the software returns to 7.1.
Note! To extend the lifetime of the lamps,
the ventilators will continue to run for
cooling. After 3/6 (IR/UV) minutes they turn
off automatically. The UV curing cannot
be restarted until after 2 minutes after
cooling due to that the hot UV-lamp will
not ignite. Note! When the drying program
is completed the temperature control will
automatically reactivate.
6
Putty 6 Topcoat
Filler Bright 7 Clearcoat
Filler Dark 8 Plastic Filler
Waterbase 9 Plastic Topcoat
Basecoat 10 Plastic Clearcoat
Distance check
Start drying
Program graph (only on IR
Program values
Energy consumption
Drying complete
11 Final boost
12 Soft cure
13 UV Putty
14 UV Filler
15 UV Clearcoat
Stop or cancel
returns to 7.1.
Use arrow keys
to set numbers.
The program
returns to 7.3.1.
The program
returns to 7.3.1.
The program
returns to 7.3.1.
GB
7.3 Edit
7.3.1 Properties
The values of the chosen program will
show on the display. By pressing the
"Temperature control" button the software
switches between the properties with and
without the temperature control. A change
in either property is independent of the
other one. See chapter 8.1 for more info.
7.3.2 PIN Code
Use the arrow keys to set the correct
digit. Press enter to confirm and to edit
the second, third and fourth digit in the
advanced PIN code.
Note! An entered PIN code is valid for all
entries until the main switch is turned off.
See chapter 9.2 for "advanced PIN code".
7.3.3 Edit program parameters
When marked, change the value of the
parameters with the arrow keys. Press
enter to change the next value and so on.
Pressing enter for the last value directs the
user to editing of program position and
name.
Press cancel to exit to 7.3.1 without saving
any parameters.
7.3.4 Edit prog. name
When marked, change the program name
with the arrow keys. Press enter to confirm
and to edit the next symbol.
7.3.5 Expansion of the program
steps
When the drying process requires more
than the two standard steps, you can
expand the number of steps in the drying
cycle by linking to the next program.
Start from point 7.3.4 and press "Enter"
repeatedly until the "Link to next program"
appears on the screen. Select with the
arrow keys "Yes" or "No", and then press
"Save". The link to the next program will
remain until it is deactivated (No).
Note! A UV program cannot be linked to
a new UV program due to the necessary
cooling time.
714812 rev 4