Wolf Garten Robo Scooter 300 Instrucciones De Funcionamiento página 92

9.2. Detailed Error Codes
If the above table (Section 9.1) does not give enough information to help solve the problem, then press the LEFT
arrow while the error code is displayed in order to receive a number that gives more details about the problem and
refer to the table below:
Display Message
Mow
8 8 9 8 Overheat
Drive Overheat
8 8 9 9
No wire signal
8 8 9 A
Front wheel
8 8 9 B problem
Button pressed
8 8 9 C
Low
8 8 9 D
temperature
Rain detected
8 8 A 8
Check mowing
8 8 A 9
height
Check mowing
8 8 A A
motor
Check power
8 8 A E
Base problem
8 8 A D
Start Elsewhere
8 8 A F
Cross Outside
8 8 A G
Probable Cause/Event
The mowing motor has been working under a
@
severe load for too long.
The drive motors have been working under a
@
severe load for too long.
See E3 in the above table
@
See E7 in the above table
@
One of the operating panel buttons is
@
constantly pressed.
Mower does not depart automatically from the
@
Base Station when the ambiance temperature
is lower than 5ºC (41ºF).
Information - When the temperature is below
@
5ºC (41ºF) the grass does not grow or grows
very slowly.
However Manual Depart is enabled.
The operation is delayed as the unit detects
@
rain.
The unit should resume operation 30 minutes
@
after it stops to detect the rain.
Mowing motor has faced over-current
@
conditions for too long as a result of high grass
or an obstacle that is stuck or wrapped around
the blade.
Something is preventing a blade from rotating
@
freely.
Severe grass accumulation under the mowing
deck, rope, or similar object is wrapped around
mowing blade.
Mowing motor has faced over-current for too
@
long in the Base Station before starting the
operation.
See E4 in the above table
@
The unit fails to enter the Base Station several
@
consecutive times.
Drive wheel motors have been working under
@
severe load during automatic or manual
operation.
The Perimeter Wire is too close to the edge.
@
The lawn slope is too big.
@
The unit does not succeed to turn in place at
@
the edge and it causes the mower to slip out of
the designated area.
The unit has slipped out of the Perimeter Wire
@
lope because of sloping area or wet grass.
Corrective Actions
No need for action –the unit will renew automatically
@
the operation after the mowing motor will cool
down.
No need to do anything.
@
The unit will renew the operation automatically as
@
soon as the drive motor will cool down.
Press 'OK' to confirm the message and continue
@
operation. This message is displayed to inform only.
No need to do anything.
@
The unit will renew the operation automatically as
@
soon as the ambiance temperature will rise above
5ºC (41ºF).
No need for action.
@
The message is displayed until the unit will not
@
detect rain and then will start mowing.
CAUTION – Switch off the Safety Switch before
@
checking the blade.
Inspect the blade for foreign material or debris
@
preventing rotation.
Clean out accumulated grass clippings using a
@
wooden stick.
CAUTION – Switch Off the Safety Switch before
@
checking the blade.
Remove the mower from the Base Station. Inspect
@
the blade for foreign material or debris preventing
rotation.
Adjust the Base Station position.
@
Clean the contacts with a brush or piece of cloth.
@
Check to insure the mower is not stuck, causing the
@
drive wheels to slip.
Check the ground around the mower for holes or
@
indentations. Fill with dirt and level off.
Check if the drive wheels are free to rotate and
@
nothing is blocking them.
Remove the mower away from this particular
@
location and restart operation.
Remove the wire towards the inner part of the lawn.
@
Do not include this area because of its steep slopes.
@
Fill holes and pits in the ground.
@
Increase the cutting height.
@