Technical Data - ALPHA-TOOLS TKS 800 Manual De Instrucciones

Anleitung TKS 800 AlphaTools
GB

5. Technical data

Asynchronous motor: 230 V 50 Hz
Power rating:
Temporary operation: S2 30 min.
Idle speed n0:
Carbide blade: ø 205 x ø 16 x ø 2.5 mm
Number of teeth:
Size of table w/o width extension: 513 x 400 mm
Table width extension: 513 x 202 mm
Cutting height max.: 43 mm / 90°
25 mm / 45°
Height adjustment, infinitely variable:
Tilting motor
Vacuum extraction socket:
6. Before putting the machine into
operation
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong stand.
All the covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Be sure to pull out the power plug
before performing any maintenance and/or
conversion work on the circular saw.
7.1 Putting up the table width extension (Fig. 1)
The table width extension (21) can be hooked
onto the left and right-hand side of the saw table
(1).
Swing down the table supports (13).
Adjust the knurled screw (19) until the table
width extension (21) is level with the saw table
(1).
Insert the cross stop (8) in the runner slot (a) of
the saw table (1).
16
12.02.2003 15:46 Uhr
7.2 Fitting the blade (Fig. 2/3)
Caution! Pull out the power plug.
Slacken the chip box cover (22) by undoing the
800 W
fastening screws (23) and swing upward.
Undo the nut (24) with the ring wrench (30) while
2950 rpm steadying the outer flange (25) with the face
spanner (31).
Important! Turn the nut in the same direction of
20
rotation as the blade (4).
Take off the outer flange (25) and remove the
old blade (4) by pulling it down and off the inner
flange at an angle.
Clean the mounting flange.
Fit the new blade in reverse order.
0 - 43 mm
Important! Note the running direction (see the
0° - 45°
arrow on the blade).
ø 35 mm
7.3 Adjusting the splitter (Fig. 4-6)
Remove the saw blade guard (2) (see 7.4).
Take out the table insert (6) (see 7.5).
Slacken the two hexagon socket-head screws
(32).
Adjust the splitter (5) so that the gap between the
saw blade (4) and the splitter (5) equals 3 - 5 mm
(see Fig. 6)
The splitter (5) has to be in line with the saw
blade (4) in longitudinal direction.
Retighten the two screws (32).
The setting of the splitter has to be checked each
time after changing the saw blade.
7.4 Fitting the blade guard (Fig. 6)
Move the splitter (5) into its upper position.
Place the blade guard (2) on the splitter (5) and
align.
Insert the screw (27) through the hole in the
blade guard (2) and the splitter (5), and secure it
with the nut.
Dismantle in reverse order.
Important: The blade guard (2) must be able to
move without obstruction.
7.5 Replacing the table insert (Fig. 4)
Important! Pull out the power plug.
Remove the 6 screws (28).
Take off the blade guard (2) (see 7.4).
Lift the worn table insert (6) up and out.
Fit a new table insert in reverse order.
Seite 16