Electrical Connection - Bobrick InstaDry B-7125 Instrucciones De Instalación

Secadores de manos
Ocultar thumbs Ver también para InstaDry B-7125:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 4
FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL
BUILDING CODE. UNIT MUST BE INSTALLED BY
A QUALIFIED LICENSED ELECTRICIAN
1. Hold the Installation Template against the wall in the desired
location of the installed dryer. See recommended mounting
heights above.
2. Make sure line on template representing bottom of dryer
mounting base is horizontal and located at the desired height
above floor.
NOTE: Surface-mounted electrical supply entry is located in the
lower right corner of the mounting base. Surface-mounted supply
cable should be fitted in a conduit.
3. For brick, stone and concrete walls, drill four 0.315" (8mm)
holes to suit provided wall plugs 0.315" x 1-1/4" (8 x 45mm)
and screws #10 x 2" (4.8 x 50mm) long. See template for
wall plug and screw installation details. For plaster or dry
wall construction, provide concealed backing to comply with
local building codes and secure with four #10 (4.8) round-
head sheet-metal screws or 3/16" (5mm) toggle bolts (not
furnished).
4. Fasten mounting base securely to wall.
WARNING: TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL CONNECTION.
FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODE. UNIT MUST BE INSTALLED BY A QUALIFIED
LICENSED ELECTRICIAN
1. Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In the United States and Canada use
No. 18 wire (18 AWG). Maximum overall dimension of supply cable must be 14mm (.55 inches).
2. Wiring Instructions:
a. This appliance is intended for connection to fixed wiring.
b. A fused means for disconnection in all poles must be provided in the fixed wiring in accordance with the wiring rules.
c. Check that the electrical rating shown on the Hand Dryer (rating label) is compatible with the electrical supply.
d. WARNING: THIS PRODUCT MUST BE EARTHED.
e. Installation and wiring must conform to current IEE Regulations (UK), local or appropriate regulation (other countries).
f. For 115 Volt-Dryers: Connect ground wire to ground terminal marked
neutral or white wire to terminal marked N.
g. For 208–240-Volt Dryers: Connect ground wire to ground terminal marked
marked L1, neutral wire colored white or blue to terminal L2.
3. Secure electrical wire in strain relief clamp provided on mounting base.
1. To replace cover, put cover up to baseplate and engage.
Push bottom of cover to engage with cover bolts (see
illustration.)
NOTE: Space between cover and wall must be the same on all
four sides.
A
1. Turn electrical power supply on. Position hands under nozzle and dryer should turn on. Remove hands
from under nozzle and dryer should stop.
Installation of Mounting Base

Electrical Connection

Replace Cover
B
C
Check Dryer Operation
Form No. 7125-69_ii (Rev 12/22/17)
{
1
>
0.5m
X
X
4 B
4 A
8
N L
A
x 2
WARNING: TURN ELECTRICAL POWER SUPPLY OFF
BEFORE MAKING ELECTRICAL CONNECTIONS. DRYER
MUST BE GROUNDED (EARTHED).
, the black or hot wire to terminal marked L1 and
. Supply wire colored black or brown to terminal
2. To tighten cover bolts, insert Allen
wrench into cover bolts on bottom
of cover. Turn CLOCKWISE until
both bolts are tightened.
NOTE: Do not over tighten cover
bolts. Over tightening cover bolts may
damage cover.
© 2017 Bobrick Washroom Equipment, Inc.
3
B
A
C
x 2
5
6
1.
8mm
2.
x 4
3.
L
N
B
C
1.0mm
2
10
4 A
4 B
1.0mm
2
x 2
3

Publicidad

Tabla de contenido
loading

Tabla de contenido