Packing And Transport; Tool Use; Precautions For The Use - CAMPAGNOLA NEXI Manual De Uso

• Do not reverse the polarity of the connections or excessively discharge the battery.
• Do not connect the battery to car chargers or cigarette lighter sockets.
• Do not use the battery for tools which are other than those indicated by the Manufacturer.
• Do not come into direct contact with lithium battery cells.
• Do not put the battery into microwaves or containers with high temperatures or high pressures.
• Do not use the battery in case of fluid loss.
• Do not use the battery if it shows signs of corrosion or a visible deformation or if it smells unpleasantly.
• Do not use the battery in an electrostatic environment (over 64V)
• If your skin or clothes come into contact with the battery fluid, rinse them immediately with water.
• Keep the batteries fully charged when the tool is not used for long periods.
• Always disconnect the charger from the electrical network when the batteries are charged up.
• Always disconnect the batteries from the charger after recharging.

Packing and transport

The unit is packaged by the Manufacturer and sent in a carrying case
WARNING!
The handling of loads must be carried out in compliance with the current workplace safety rules.
case for storing the tool for medium or long periods or for sending the packed product to an Authorized Service
Point for repairs.

Tool use

• Firmly hold the tool with one hand and press the ON/OFF button (7) with the other.
• By means of the corresponding button (9) select the right tying regulation according to the branch diameter.
• Put the front tying opening (10) onto the branch to tie and press the trigger (6). The product has been designed to tie
branches of vineyard or of other kinds of plants having a maximum diameter of 25 mm.
• When using the tool, firmly hold it with one hand and always keep it at least 10 cm away from the other and from any
other body part.
• The tying operation ends when the hook (4) normally returns to its initial position and does not show any interference
due to foreign material.
• At the end of the tying operation hold the tool tight when detaching it from the branch.
• Go on with the following tying operation.
WARNING!
Use the tool only for the purposes described in par. "Product description". Any other use could cause injuries.
•
• Operate the tool only when it is inserted among the branches. Any improper use causes greater tool wear and
battery consumption.
5.1.1

Precautions for the use

• Do not use abrasive degreasers or products containing solvents to rinse the tool.
• For a proper tool operation follow the instructions. In case of damage, do not use the tool, the battery (14) and its
charger (17).
• Do not use the tool when it does not work properly.
• Always remove the battery (14) before any operation of adjustment or parts replacement or before storing the tool at
the end of the work session. This allows to reduce the residual risks due to an involuntary tool activation.
• The tool must be operated following the instructions and the way of use indicated in this manual, taking into consider-
ation the environment and the kind of work to carry out. It is recommended not to use the tool in case of poor psycho-
physical skills or in situations which are different from the indicated ones, as it could be very dangerous.
• When the tool is working, keep your free hand at least 5 cm away from it. Do not put your hand into the front tying
opening (10).
• Do not use the tool to tie branches having a diameter over 25 mm, otherwise it could stop.
• During the tying operation, the tool must be kept perpendicular to the branches. Do not rotate or move it while tying.
Damages to the tool caused by incorrect operations are not covered by warranty.
• Do not use the tool during rainy days.
• After each use it is recommended to disconnect the tool from the battery (14) and to put both into the carrying case.
• If the tying tool gets stuck on the branch while working, do not try to manually release the tie supplying hook (4) or the
stuck twist tie, if any, without first switching off the tool. Then move the hook (4) manually to free the tool.
• Check whether the diameter of the tied branch is not over 25 mm and whether the tying tool has not been blocked by
some stuff.
• To ensure its correct lifespan as well as to save power, do not overload the tool. Do not use it for branches having a
diameter over 25 mm
Page 28
Use and maintenance manual – Translation of
original Instruction.: 00, Date 25/09/2020
Use
the carrying