Compressed Air Connection - Telwin SPL 60/3 Manual De Instrucciones

- RANGE 1 - (Duty Cycle); X
Absorbed current
Power
Power factor
- GAMMA 2 - (Duty Cycle); X
Absorbed current
Power
Power factor
- GAMMA 3 - (Duty Cycle); X
Absorbed current
Power
Power factor
- Delayed power fuses
OUTPUT
- Loadless tension
- RANGE 1: (Duty Cycle) X
Conventional cutting tension
Conventional cutting current
Cutting capacity (carbon steel)
- RANGE 2: (Duty Cycle) X
Conventional cutting tension
Conventional cutting current
Cutting capacity (carbon steel)
- RANGE 3: (Duty Cycle) X
Conventional cutting tension
Conventional cutting current
Cutting capacity (carbon steel)
NOTE (1)
400V voltage standard. See paragraph "CONNECTION TO
ELECTRIC NETWOTK" in order to make a change in power
supply.
Figure (A) the drawing shows machine
dimensions
Figure (A1) Plate of data
a Utilisation data (cutting circuit).
1- No load voltage (U ).
0
2- Cutting current-voltage (I /U )
3- Duty cycle (X) in use.
b Main power supply data.
4- Number of phases and mains frequency 50/60 Hz.
5- Mains voltage (U ).
1
6- Maximum RMS current absorbed I1max and nominal
RMS current absorbed I .
c General information
7- Level of protection for sheathing
8- Symbol for apparatus suitable for environments with
increased risk of electric shock
9- Symbol for type of process
10- Energy conversion chart
11- Standards of reference
12- Apparatus identification
13- Name of manufacturer
14- Range of cutting current (min/max) and corresponding
conventional arc voltage.
15- Manufacturer's serial number
MANUAL TORCH FOR HP PLASMA
CUTTING HP 150
- Gas used
- Compressed air pressure
(%) 100 100
(A) 38
(kW) 9.8 9.8
(cosphi) 0.65 0.65
(%) 60
(A) 55
(kW) 15.3 15.3
(cosphi) 0.7 0.7
(%) 35
(A) 72
(KW) 20.5 20.5
(cosphi) 0.72 0.72
A 40
(V) 236
(%) 100
(V) 125
(A)
(mm) 3 - 18
(%)
(V) 135
(A)
(mm) 5 - 25
(%)
(V) 140
(A) 120
(mm) 7 - 35
2 2
1eff
: dry compressed air
: 5,5 bar
- Total flow rate (for
22 Plasma and cooling)
- Striking system
- Cutting current
60 Data Cycle X = 60%
32 Data Cycle X = 100%
- Cutting mode
in contact
35 with spacer
42
- Cable length
25
WARNING !
SAFETY OF PLASMA CUTTING SYSTEM.
Only this model of torch and its coupling with the current
source as shown on "TECHNICAL DA TA" ensure the
efficacy of the safety measures adopted by the constructor
60
(interblockage system).
- DO NOT USE torches and relative using parts for a
60
different purpose.
- DO NOT TRY TO COUPLE torches built for cutting
90
procedures or for welding to the source of current if they
are not described in these instructions.
35
- IF THESE RULES ARE NOT OBSERVED serious
dangers may occur both to the user and to the machine.
3.INSTALLATION
ASSEMBLAGE OF SEPARATE PARTS:
Take "SPL" plant from packing and proceed to sent the
wheels according to the following scheme:
Figure (B) wheel setting drawing

COMPRESSED AIR CONNECTION

- Arrange a compressed air distribution line having the
following minimum features:
- SPL 60/3
Air pressure 5 bars; capacity 140 L/min.
- SPL 90/3 and SPL 150/3
Air pressure 5,5 bar; capacity 220 L/min.
WARNING !
Air with considerable quantities of humidity or oil may
cause an excessive wear of the parts or even damage
the torch.
If there are any doubts about the quality of compressed air
available, we advise to use an air dryer, to be installed above
the entry filter.
Connect, by means of a flexible piping, the compressed air
line to the machine, using one of the connectors included to
be set on the entry air filter, which is on the rear of the
machine.
Figure (C) compressed air connection
WARNING !
Do not exceed maximum entry pressure of 8 bars.
CONNECTION TO ELECTRIC LINE
- The machine may be connected exclusively to three
- 18 -
: 220 L / min
: HF and Pilot Arc
:
:
:
: GAMMA 1 (60A)
GAMMA 2 (90A)
GAMMA 3 (120A)
:
drawing
/ A
150 A
/
6 m