Nice Era Mat MHT-USA Serie Instrucciones Y Advertencias Para La Instalación Y El Uso página 12

A new transmitter can easily be memorized with the same characteristics as that of the old one by following the procedure in table A18.
The "new" transmitter will inherit the characteristics of the old one, i.e. if the old transmitter was memorized in Mode 1, the new one will also
function in Mode 1, if the old transmitter was memorized in Mode II then the button of the new transmitter will be associated to the same
command as that of the old one.
Table "A18" Memorizing other transmitters
1. Press and hold down the button to be memorized of the new transmitter
(for approx. 3 seconds) then release it
2. Press and hold down the button to be memorized of the old transmitter
(for approx. 3 seconds) then release it
3. Press and hold down the button to be memorized of the new transmitter
(for approx. 3 seconds) then release it
4. Press and hold down the button to be memorized of the old transmitter
(for approx. 3 seconds) then release it
5. The memorization of the new transmitter is confirmed with 3 beeps
Note: If the memory is full (14 transmitters), 6 beeps will indicate that the transmitter cannot be memorized.
7) Disposal
This product is an integral part of the automation system it con-
trols and must be disposed of along with it.
As in installation operations, at the end of the product's lifespan,
disposal operations must be performed by qualified personnel.
The product is made of various types of materials: some of them
may be recycled, while others must be scrapped. Seek information
on the recycling and disposal methods envisaged by the local regu-
lations in your area for this product category.
Warning! – Some parts of the product may contain polluting or hazar-
dous substances which, if released to the environment, may cause
serious damage to the environment or to human health.
8) What to do if...
When the motor is switched on, no beep is emitted.
Make sure the motor is powered at the correct mains voltage; if the
power supply is correct there is probably a serious fault and the
motor needs to be repaired by the customer service department.
The motor does not move after a command is given.
• If it has been working up until then, it may be that the thermal pro-
tection device has cut-in, therefore wait a few minutes for the
motor to cool.
• Make sure that there is at least one memorized transmitter, check-
ing that the motor emits short beeps when switched on.
• Make sure that the transmitter and motor are communicating,
keeping button n (2) of a transmitter (memorized or not) pushed
for at least 5 seconds, if a beep is heard this means that the motor
is receiving the signal from the transmitter therefore go on to the
last control; otherwise perform the next control
• Check the correct emission of the transmitter radio signals with the
following empirical test: push a button and rest the LED against the
aerial of a normal household radio (ideally inexpensive) that is
switched on and tuned in at 108.5 Mhz FM or as close as possi-
ble; a low sound should be heard with crackling pulses
• Check, by slowly pushing one at a time, all of the transmitter but-
tons, if none of them command a movement of the motor, this
means that the transmitter is not memorized.
After a radio command, 6 beeps are heard and the
manoeuvre does not start.
The radio control unit is unsynchronised, repeat the transmitter
memorization process.
11
a short troubleshooting guide!
As indicated by the symbol alongside, dispo-
sal of this product with household waste is
prohibited. Separate the waste into catego-
ries for disposal, according to the methods
established by current legislation in your
area, or return the product to the retailer
when purchasing a new version.
Warning! – Local legislation may impose heavy fines in the event of
illegal disposal of this product.
After a command, 10 Beeps sound and then the manoeu-
vre begins.
The auto-diagnosis of the memorized parameters has revealed a
fault (positions, programming the operationsare are incorrect). Delete
and repeat programming if necessary.
When raising the motor stops before reaching the set
position (pos. "0", pos. "I") and then makes three attempts
to start again.
This is normal: when an excessive force is detected while raising, the
motor is switched off for about 1 second and then attempts to finish
the manoeuvre; check if there are obstacles that are blocking the
movement.
When lowering the motor stops before reaching the set
position (pos. "1", pos. "I").
This is normal: when an excessive force is detected while raising, the
motor is switched off; check if there are obstacles that are blocking
the movement.
The motor only moves in "hold-to-run".
If positions "0" and "1" haven't been programmed the up and down
movement of the motor occurs in hold-to-run only. Program posi-
tions "0" and "1".
Positions "0" and "1" are programmed but it has a "hold-
to-run" movement when lowering.
The emergency override mechanism has probably been used or the
motor has been switched off for over 24 hours. Retract the awning
until position "0" is reached.
Example
New >3s
Old >3s
New >3s
Old >3s