Control Panel Features - Vimar Elvox RS15 Manual Para El Conexionado Y El Uso

POINT A -

CONTROL PANEL FEATURES

J4
J1
S3
TR2
J9
J5
J2 J3
RELAY AND MOTOR COMMAND
K1 => Opening direction command
K2 => Closure direction command
Q4 => TRIAC - Opening and Closing motor command
Q5 => Blinker command
POINT B
- SETTINGS
DIP 1 (ON) MOTOR ROTATION DIRECTION CHECK (See
Point C)
DIP 2 (ON) PROGRAMMING (See Point D)
DIP 1-2 MEMORIZATION/CANCELLATION OF RADIO
CONTROL CODES (POINT E)
DIP 3 ON - Automatic Closing ENABLED (max 5 min)
OFF - Automatic Closing DISABLED
DIP 4 ON - AUTOMATIC Radio Receiver Command
OFF - STEP BY STEP Radio Receiver Command
DIP 5 ON - AUTOMATIC single pulse command (K BUTT.)
OFF - STEP BY STEP single pulse command (K BUTT.)
DIP 6 ON - Operation in PARK MODE
OFF - Operation in NORMAL MODE
WARNING: The PARK MODE enables or disables some features
and commands:
If NORMAL MODE is enabled, OPEN2 command, OK CLOSE
command and TLC (Traffic Light Control) input, are not enabled.
If PARK MODE is enabled all commands are enabled.
DIP 7 OFF
DIP 8 ON - in PARK MODE the OPEN2 button is always enabled
OFF - in PARK MODE the OPEN2 button works if there is no
vehicle on the magnetic sensor connected to the TLC
input (TLC contact opened).
DIP 9 OFF
J1
J2
J8
J3
J4
J5
J7
J6
J6
J7
J8
J9
J10
2
J10
S3
TR2
EN
L-N Main power supply 230 Vac 50/60 Hz upon request)
COM Common contact
LSC Closing limit switch contact (NC)
LSO Opening limit switch contact (NC)
LSSC Closing slowing down limit switch contact (NO)
LSSO Opening slowing down limit switch contact (NO)
TLC Vehicle presence signal (NO) (only when switched to PARK
mode)
PHOT. NC Photocells contact (NC)
EDGE NC -
COM Common contact
D+ TEST Safety strip self-test power supply +12 Vdc 500 mA max
D+ Accessories power supply +12 Vdc 500 mA max
D- Accessories power supply -12 Vdc 500 mA max
OPEN 2 Barrier opening button 2 contact (NO) (only when switched to PARK mode)
SIGNAL Barrier open signal 12 Vdc
Buzzer - Acoustic signal connection (12 Vdc max 200 mA)
AERIAL Radio antenna
Blinker (max 40 W)
U - MOTOR Motor common connection
V-W - MOTOR Motor inverters and condenser connection
OK CLOSE Immediate closure command contact (only when switched to PARK mode)
OPEN 1 Open1 button contact (NO)
CLOSE Close button contact (NO)
STOP Stop button contact (NC)
K BUTT. Single pulse button (NO)
COM Common contact (common line for all the commands and safety inputs)
PROBE -
RADIO
Built-in radio module
AUX. ATT.
-
SW PARK DO NOT TOUCH THE JUMPER!
IF REMOVED THE OPERATOR DOES NOT FUNCTION!
SW RADIO DO NOT TOUCH THE JUMPER!
IF REMOVED THE RADIO SYSTEM DOES NOT FUNCTION!
PROG. Programming button
TRIMMER LOW Slow closure speed electronic regulator
SPEED
DIP 10 ON - after the blackout the boom arm automatically closes
OFF - after the blackout the boom arm remains still on the point
it was when blackout occurred
DIP 11 OFF
DIP 12 OFF
DIP 13 ON - Blinker operation with intermittent power supply
OFF - Blinker operation with fixed power supply
DIP 14 - selecting type of barrier operation (see table 1)
DIP 15 - selecting type of barrier operation (see table 1)
DIP 16 - selecting type of barrier operation (see table 1)
DIP 14 DIP 15 DIP16 STANDARD BARRIER
OFF OFF OFF EBR1
OFF OFF ON EBR1
ON OFF ON EBR1
ON OFF OFF EBR2
LOW SPEED REGULATOR
Slow-speed regulations are carried out by turning the Trimmer LOW
SPEED, it permits to vary the speed of the motor in approaching to
the closing position (turning clockwise to increase the motor speed).
This kind of regulation is not available in approaching to the opening
position.
The starting of slowing down is controlled automatically by the limit
switches at approximately 30° before reaching the complete opening
and closing position.
LED WARNING
DL1 - Programming activated (red)
DL2 - Stop contact (red)
TABLE 1
with a 3m boom arm code EBRA.380
with a 4m boom arm code EBRA.480
with a 5m boom arm code EBRA.580
13