Publicidad
Idiomas disponibles
Idiomas disponibles
Do not use tool if switch does not turn it
"ON" or "OFF". Any tool that cannot be
controlled
with the switch
is dangerous
and
must be repaired.
Disconnect
the plug from the power
source
before
making
any adjustments,
changing accessories,
or storing
the
tool.
Such preventive
safety measures
reduce the risk of starting the tool
accidentally.
Store idle tools out of reach
of children
and other untrained
persons.
Tools are dangerous
in the hands of
untrained users.
Maintain tools with
care. Keep cutting
tools sharp
and clean.
Properly
maintained
tools, with sharp cutting
edges
are less likely to bind and are easier to
control. Any alteration or modification
is a
misuse and may result in a dangerous
condition.
Check
for misaUgnment
or binding
of
moving parts, breakage
of parts, and any
other condition
that may affect the tools
operation.
If damaged,
have the tool
serviced
before using. Many accidents
are
caused by poorly maintained
tools. Develop
a periodic
maintenance
schedule for your
tool.
Use only accessories
that are
recommended
by the manufacturer
for
your
model.
Accessories
that may be
suitable for one tool, may become
hazardous
when used on another tool.
Service
Tool service must be performed
only by
qualified
repair personnel.
Service or
maintenance
performed
by unqualified
personnel could result in a risk of injury.
For
example:
internal wires may be misplaced
or pinched,
safety guard return springs may
be improperly
mounted.
When servicing
a tool, use only identical
replacement
parts. Follow
instructions
in
the Maintenance
section
of this manual.
Use of unauthorized
parts or failure to
follow Maintenance
Instructions
may create
a risk of electric shock or injury. Certain
cleaning
agents such as gasoline, carbon
tetrachloride,
ammonia,
etc. may damage
plastic parts.
Accessories
must be rated for at least
the speed recommended
on the tool
warning label.
Wheels and other
accessories
running over rated speed can
fly apart and cause injury.
Hold tool by insulated
gripping
surfaces
when performing
an operation
where the
cutting
tool may contact
hidden
wiring
or
its own cord.
Contact with a "live" wire will
make exposed
metal parts of the tool "live"
and shock the operator.
If cutting
into
existing walls or other blind areas where
electrical
wiring may exist is unavoidable,
disconnect
all fuses or circuit breakers
feeding this worksite.
The following
warning
is intended
for flex
shaft tools and accessories:
Do not
operate
the flexible
shaft with a sharp
bend.
Over bending the shaft can generate
excessive
heat on the jacket or hand piece.
The recommended
minimum
is 6" radius.
Always
disconnect
the power
cord from
the power
source
before making
any
adjustments
or attaching
any
accessories.
You may unexpectedly
cause
the tool to start leading to serious
persohal
injury.
Be aware of the switch location,
when
placing
the tool down or when picking
the tool up. You may accidentally
activate
the switch.
The following
warning is intended for flex
shaft tools and accessories:
Always hold
the hand piece firmly in your hands
during the start-up.
The reaction torque of
the motor, as it accelerates
to full speed,
can cause the shaft to twist.
Always
hold the tool with two hands
during
start-up.
The reaction torque of the
motor can cause the tool to twist.
Always
wear safety goggles and dust
mask.
Use only in well ventilated
area.
Using personal safety devices and working
in safe environment
reduces risk of injury.
After changing
the bits or making
any
adjustments,
make sure the collet
nut
and any other adjustment
devices
are
securely
tightened.
Loose adjustment
device can unexpectedly
shift, causing loss
of control, loose rotating
components
will
be violently thrown.
Do not reach
in the area of the spinning
bit. The proximity
of the spinning
bit to your
hand may not always be obvious.
Publicidad
