Internal Cleaning; External Cleaning - Tecfrigo BRIO 96 Instalación Y Uso

Operator's guide:
1)Unpacking instructions
2)Adjusting the shelves

3)Internal cleaning

I

4)External cleaning

5)Connection to the mains
UK
6)Controls
7)Checking correct operation before use
D
8)Internal cleaning
9)Replacing the internal lights
E
F
! WARNINGS
NL
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
P
1. Adults should operate this appliance only. Do not allow children to use the controls or play with it. 2
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
S
installation of the appliance should be carried out by a qualified electrician or other competent person.
4 . Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
DK
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. 6
7 . The manufacturers of this appliance accept no responsibility for the consequences of misuse in
FIN
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice. 8
B
near sources of heat, such as radiators, stoves, etc.
for at least 30 cm.
GR
edges. 12 . If damp air or products to be refrigerated should cause ice to form on the evaporator, we
recommend stopping the compressor and placing the goods in special refrigerated containers, kept at the
CZ
same temperature, until defrosting is completed;if this is not carried out the compressor will continue to
operate leading to a wasteful consumption of electricity and poor performance.
EE
working and unused, it is indispensable to keep the door open at least 10 cm.
light up if the refrigeration is off.
LV
LT
!
Our products are for internal use only – do not install outside restaurants, shops.
H
M
1. UNPACKING INSTRUCTIONS
CARDBOARD PACKAGE 1a
PL
Remove the nails from the wooden crate with care.
appliance and pallet or crate. . Lift up the appliance. . Remove the pallet or crate. . Let down the
SK
appliance onto a flat and level surface, and adjust the feet.
package before disposal. . Separate the packaging materials to facilitate disposal (see figure 1).
SLO
2. ADJUSTING THE SHELVES
1. Raise the shelf.
making sure there is a shelf on the left and on the right (see figure 2).
3. INTERNAL CLEANING
1
. Remove the protective film from the trays.
sponge and neutral detergents.
4. EXTERNAL CLEANING
1. Use the same products as used for the internal cleaning
steel panels and from the grilles.
5. CONNECTION TO THE MAINS
1 . Ensure that the voltage and frequency of the mains supply are the same as those indicated on the
rating plate attached to the appliance (A).
following characteristics:
out on the rating plate
as stated on appliance rating plate and ID sensitivity of 30 mA
explosion (AD) in the room.
provided. The cable of the appliance is H05 VVF, designed for internal use.
been transported or stored overturned, let is rest in its correct position for at least 3 hours before hooking
it up to the mains. . Insert the plug into the socket (do not use three-way adapters and reduction
adapters) (see figure 3).
5
. Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance
11 . Ensure that the products displayed on the shelves and grills do not hang over the
. Cut the strap and lift up the cardboard package.
3
7
2. Turn it downwards. . Remove it. . Put it in the new position, in reverse order,
It is properly earthed
a)
It complies with the IEC regulations: magnetothermal differential switch with IN
. c)
4. Make sure the environment is suitable for the power supply cable
5
Operator's guide
Maintenance manual (Page 48):
1)Cleaning the condenser
2)Cleaning the evaporator
3)Replacing a sliding glass door
4)Wiring diagram diagram of refrigeration unit
10 . Keep the ventilation grills free from obstruction
2. Insert the forks of a forklift truck between the
4
6. Make sure there is nothing left in the
3 4
2.
Clean the internal parts and glass surfaces with a soft
. 2 . Remove the protective covering from the
2. Ensure that the socket to supply the electricity has the
It fulfils the requirements of the rated current as set
.b)
. 3. Ensure that there is no danger of
6
3
9
13 . If the appliance is not
14. Do not keep the neon
WOODEN CRATE 1b.
5
N.B. : if the equipment has
. It