Technical Specifications - Slendertone ABS6 Manual De Usario

T
ECHNICAL SPECIFICATIONS
Caring for your controller
Your controller should not be allowed to get wet or be left in excessive
sunlight. It may be cleaned regularly using a soft cloth, lightly dampened
in soapy water. Do not allow the interior of your controller to become wet.
Do not use detergents, alcohol, spray aerosols or strong solvents on your
controller.
Access to the interior of the controller is not required for maintenance
purposes.
If your product is damaged, you should not use it but should return it to
or your local distributor for replacement or repair. Repairs,
SLENDERTONE
service and modifications may not be carried out by anyone other than
qualified service personnel authorised by
: Under no circumstance should anything other than the correct
IMPORTANT
type of batteries – (rechargeable batteries 3.6V NiMH) be used with your
controller. These can be purchased from
Disposing of the gel pads and batteries
Used gel pads and batteries must never be disposed of in a fire but in
accordance with your country's national laws governing the disposal of
such items.
:
NOTE
- The signal gradually increases to a peak intensity level at the start of the
contraction phase (i.e. ramp up) and gradually decreases to nothing at
the start of the relaxation phase (i.e. ramp down). When the the start of the relaxation phase (i.e. ramp down). When the
flashing, the stimulus is significantly reduced.
Accessories:
You can purchase all accessories at www.slendertone.com. Under no
circumstances should anything other than
used with your charger or
SLENDERTONE
Any others may not be compatible with the product and could degrade
the minimum safety levels.
6 Pads: • 1 large gel pad (Type 732)
SLENDERTONE ABS
• 2 small gel pads (Type 733)
Battery Pack (3.6V, NiMH)
Battery Charger:
EU: 2504-0321 + 2504-0324 + 2504-0325;
Australia: 2504-0321 + 2504-0327;
Charger complies to EN 60950, Input: nominal voltage 100-240V, frequency
50-60Hz, current 125mA. Do not use any other chargers or any other power
supplies.
Classification: Internally powered equipment, Class II charger, Type BF
applied parts.
Product Type: 390
Intended use: Muscle stimulator
Waveform: Symmetrical bi-phasic square waveform when measured into a
resistive load.
Environmental Specifications:
Operating Range: Temperature: 0 - 35°C (32 - 95°F)
Humidity: 20 - 65 % RH
Temperature Range: 0 - 55°C (32 - 131°F)
Transport &
Humidity: 10 - 90 % RH
Storage Range:
Attention:
This product can deliver currents in excess of 2mA/cm
electrodes.
16
.
SLENDERTONE
Customer Care.
SLENDERTONE
symbol is symbol is
accessories be
SLENDERTONE
controller (Type 390).
SLENDERTONE
US/Japan: 2504-0322;
Korea: 2504-0321 + 2504-0323
if used with incorrect
2
Description of your controller's symbols:
There are a number of technical markings on your controller. These can be
explained as follows:
The product is manufactured for Bio-Medical Research Ltd,
Parkmore Business Park West, Galway, Ireland.
The controller requires 1 x 3.6 volt (NiMH) DC battery pack DC is indicated
by the symbol:
The Output Frequency indicates the number of pulses per second transmitted
by the controller. This is measured in hertz, which is indicated by "Hz".
Output (RMSA) means the maximum output root mean square current for
each channel.
Output (RMSV) means the maximum output root mean square voltage for
each channel.
This symbol means "Attention, consult the accompanying documents".
!
This symbol means type BF applied parts (gel pads).
This symbol on your unit is to indicate conformity to the requirements
of the Medical Device Directive (93/ 42/EEC). 0086 is the number
0086
of the notified body (BSI).
The CE mark applied also indicates that this equipment complies
with the requirements of the ROHS Directive (2011/65/EU) for the
Restriction of Hazardous Substances in Electrical and Electronic
Equipment.
SN stands for 'serial number'. On the label on the back of the controller is
the serial number specific to this controller. The letter preceding the number
indicates the year of manufacture, where "U" denotes 2015, "V" denotes
2016 etc.
The belt's batch number is represented on the belt packaging, by the
number corresponding with the LOT symbol.
Conforms to UL STD 60601-1.
Certified to CAN/CSA.
STD C22.2 NO 601.1
At the end of the product lifecycle, do not throw this product into the
normal household garbage, but bring it to a collection point for the
recycling of electronic equipment.
Some product materials can be re-used if you bring them to a recycling
point. By re-using some parts or raw materials from used products you
make an important contribution to the protection of the environment.
Please contact your local authorities if you need more information
about collection points in your area.
Waste Electrical and Electronic Equipment can have potentially harmful
effects on the environment. Incorrect disposal can cause harmful toxins
to build up in the air, water and soil and can be harmful to human health.
Rated Outputs – Voltage/Currents: X:10
Parameter
Output RMSV
Output RMSA
Output Frequency
DC Component: Approx.
Positive Pulse Width: 200-300µs
Negative Pulse Width: 200-300µs
Interphase Interval:
500! 1K! 1K5!
6.4V 12.7V 12.7V
12.7mA 12.7mA 8.5mA
50-70Hz 50-70Hz 50-70Hz
0 C 0 C
200-300µs 200-300µs
200-300µs 200-300µs
100 µs 100 µs 100 µs
0 C
17