Side Broom Height Adjustment; Side Broom Replacement; Dust Filter Cleaning And Integrity Check - Nilfisk-Advance Terra 132B Manual De Uso

OPERATOR MANUAL

SIDE BROOM HEIGHT ADJUSTMENT

NOTE:
Brooms with harder or softer bristles are
available. This procedure is applicable to
each type of broom.
1. Check the correct height of the side broom from
the ground, by proceeding as follows:
2. With the machine on level ground, lower the side
broom by disengaging the side broom latch (2,
Fig. C).
3. Keep the machine stationary and allow the side
broom to rotate for a few seconds.
4. Stop the side broom and move the machine.
5. Check that the side broom pattern is as shown in
figure J. If it is different, adjust the broom height as
described in the following step.
6. Rotate the knob (12, Fig. C) clockwise or
counter-clockwise to adjust the broom height from
the ground.
7. Perform steps from 1 to 5 again to check the
proper adjustment of the side broom height from
the ground.
8. When the broom becomes too worn, adjustment is
no longer possible. Replace the broom following
the instructions in the following paragraph.

SIDE BROOM REPLACEMENT

NOTE:
Brooms with harder or softer bristles are
available. This procedure is applicable to
each type of brooms.
1. Turn the ignition key (2, Fig. B) to the "0" position.
2. Slide your hand under the side broom and press
the two tabs (1, Fig. K) inward and then push the
broom (2, Fig. K) downward to disengage it from
the four pins (3, Fig. K) on the side broom hub.
3. Install the new broom on the machine by aligning
it on the pins (3, Fig. K) and then pressing it onto
the two tabs (1, Fig. K).
4. Carry out the Side Broom Height Adjustment as
described in the previous paragraph.
10
DUST FILTER CLEANING AND INTEGRITY
CHECK
NOTE:
Besides the standard paper filter, optional
polyester filters
following procedure is applicable to each
type of filter.
1. With the machine on level ground, activate the
brake pedal (26, Fig. C) (if present), or block the
wheels.
2. Turn the ignition key (2, Fig. B) to the "0" position.
3. Disengage the hopper latch (18, Fig. C).
4. Using the handle (19, Fig. C) remove the hopper
(17, Fig. C) from the machine.
5. Rotate the filter clamp (1, Fig. L) upward
(approximately 90°) and let the top of the filter
frame (2) rotate outward.
6. Pull the dust filter (3, Fig. L) upward to remove it.
7. In a well-ventilated, outdoor area, clean the filter
by gently tapping the side of the filter (1, Fig. M),
opposite to the wire screen (2) on the ground.
8. Finish cleaning the filter by using compressed air
(3, Fig. M) of max. 6 bars ( 87 psi), blowing only
from the side protected by the wire screen (2, Fig.
M).
According to the type of filter, take care of the
following cautions:
– Paper filter (standard): do not use water or
detergents to clean it; the filter can be
damaged.
– Polyester filter (optional): to clean it, follow
the instructions mentioned in number 7
above. For better cleaning, wash the filter
with water and non-foaming detergents. This
type of washing will clean the filter better, but
it reduces the life of the filter. The use of
inadequate detergents can damage the filter.
Check the filtering medium body for cuts or
holes.
9. If necessary clean the filter compartment rubber
seal (4, Fig. L) along its perimeter and check its
integrity. If necessary replace it.
10. Install in the reverse order of removal.
NOTE:
Reinstall the filter with the wire screen (2,
Fig. M) facing the front part of the machine
(toward the fan (16, Fig. U)).
are available. The
146 0791 000(2)2004-02