STEINEL PROFESSIONAL HG 2620 E Manual De Instrucciones página 10

Technical Specifications HG 2220 E
Voltage 120 V, 60 Hz
Output 1500 W
Stage 1
Airflow rate 4 - 7 cfm
Temperature 120 - 1100 °F
50 - 600 °C
Temperature setting At thumbwheel in 9 steps
Power Cord Industrial grade rubber, double insulated
Thermal cut-out Yes
Emission sound pressure level ≤ 70dB (A)
Total vibration value ≤ 2.5 m/s
Weight without power cord 0.610 kg
Settings
Airflow rate stage 1 low airflow rate
Thumbwheel Temperature approx.
1 176 °F (80 °C)
2 230 °F (110 °C)
3 374 °F (190 °C)
4 536 °F (280 °C)
5 680 °F (360 °C)
6 824 °F (440 °C)
7 932 °F (500 °C)
8 1058 °F (570 °C)
9 1166 °F (630 °C)
Depending on how accurately the thumbwheel is set, the guide values shown may differ by up to +/- 68 °F
from the temperature actually delivered.
English
2
6 - 12 cfm
120 - 1100 °F
50 - 600 °C
/ K = 0.08 m/s
2 2
Subject to technical modifications
Airflow rate stage 2 high airflow rate
Temperature approx.
176 °F (80 °C)
230 °F (110 °C)
356 °F (180 °C)
500 °F (260 °C)
644 °F (340 °C)
788 °F (420 °C)
896 °F (480 °C)
1040 °F (560 °C)
1166 °F (630 °C)
- 18 -
Applications HG 2220 E
Shrink tubing on cables:
The shrink tubing is slipped over the section you want to insulate and heated with hot air. The tubing shrinks
by approx. 50% in diameter to give a sealed union. Shrinking is particularly fast and even using reflector noz-
zles.Sealing and stabilizing cable breaks, insulating soldered joints, gathering cable runs, sheathing terminal
blocks.
Forming PVC:
Sheeting, piping or ski boots can be softened and formed with hot air.
Soldering:
First, clean metal parts you want to join. Then, using hot air, heat the point you want to solder and offer up
the soldering wire. Use flux or a soldering wire with a flux core to prevent oxide forming.
Welding and joining plastic:
All parts being welded must be of the same plastic material. Use an appropriate welding rod.
Joining plastic sheeting:
The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then
the two sheets are firmly pressed together with a feed roller.
Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.
Shaping:
Ski boots and sports shoes can be shaped for a perfect fit.
Welding sheeting:
The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then
the two sheets are firmly pressed together with a feed roller.
Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.
- Welding all thermoplastics.
- Welding films and tarpaulins.
- Welding plastics and jointing.
- Activating and removing glues and hot-melt adhesives.
- Thawing frozen door locks, frozen water pipes, icy steps.
- Heating car-wrapping films.
- Applying edgebands.
- Shaping thermoplastics.
English
- 19 -