Cequent Performance Products T-One T-Connector Instrucciones De Instalación

Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One T-Connector
®
T-One connecteur en T
®
T-One Conector en T
®
Buick Enclave Chevy Traverse
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l'installation. Durant
l'installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
22111-037 Rev. A
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, 1/4" socket,
Wire Cutters, Test-probe
1. Locate the vehicle's towplug located under
the vehicle on the passenger side. Locate the
opening to the right of the vehicle muffler.
Reach up into opening to locate the vehicle's
grey towplug . Disconnect the mating
d
protective cover and discard. Connect the
towplug harness into mating harness.
Check to see that the mating surfaces of
the wiring connectors match. All connector
surfaces should be clean and free of dirt.
Be careful not to damage the locking tabs
and be sure that connectors are fully inserted
with locking tabs in place.
2. Route 7-Way to the center of vehicle. Mount
the 7-Way end in an accessible location with
a bracket or electrical box (not included).
NOTE
See 7-Way diagram for wire locations
3. Open rear door. Remove both taillight housing
assemblies by removing the two bolts for each
light and carefully prying the vehicle taillight
housing assembly away from the vehicle, being
careful not to break the alignment tabs
6/25/2014
d
4. Route harness containing the green wire
underneath the vehicle up through the
opening between the vehicle bumper
and body to the passenger's side taillight
pocket.Insert the T-Connector end with
the green wire into the vehicle's taillight
connector and lock into place.
WARNING
Route the wire being careful to avoid any
hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
5. Repeat step 4 for the passenger's side using
the T-Connector containing the yellow wire.
6. Under vehicle hood, locate the vehicles
fuse box. Insert fuses into positions shown.
Insert 10 Amp Fuse (Provided) in the
following location:
Position D1
Insert 30 Amp Fuses (Provided) in the
following locations:
Position D2
Position D3
g
WARNING
All connections must be complete for the
.
e
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed.
.
f
BLACK
BROWN
BLUE
e
f
PAGE 1 OF 3
7-WAY CONNECTOR
YELLOW
CAR END
As viewed from core back side where
wires are attached with screws.
D1
D2
D3
g
7. Reinstall the taillight housing assemblies,
positioning the vehicle wiring harness between
the housing and the vehicle body. Secure the
remainder of the T-connector harness with
the cable ties provided, to prevent damage
or rattling and being careful to avoid any
areas that would cut or pinch the wire.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: (10 amps)
• Max. tail lights: (10 amps)
• Max. backup: (10 amps)
• Max. power circuit: (30 amps)
• Max. trailer brakes: 3 Axles/6 brakes
(20 amps)
Read vehicle's owners manual &
instruction sheet for additional information.
GREEN
RED
WHITE