Publicidad
Idiomas disponibles
Idiomas disponibles
Grill Lighting
Instructions
1 Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions, tf a hose is damaged in any way, do not
use your gdll before replacing the hose with an authorized
part from the Parts List
Also make sure all gas supply
connections
are securely tightened
2 Familiarize
yourself with the safety and Use and Care
instructions in this guide. Do not smoke while lighting grill
or checking
gas supply connections.
3 Be sure the Natural Gas Line is attached to the gas source
(or if using a professionally converted LP grill, be sure the
LP Gas tank is filled )
4 Open the Grill Lid
Failure to replace a faulty hose, secure gas supply
connections or to open the Lid before proceeding
to
the Lighting
Procedures
could
result
in a fire or
explosion
that
could
cause
serious
bodily
injury,
death, or property
damage.
Burner Control Knobs on Control Panel
,@o
@i
Main Burner
,\
\
Rotisserie
Infrared
Burner
Bur ner
Rotisserie
Burner
Lighting
Instructions
1Follow steps 1 through 5 of the Grill Lighting Instructions
2 Push and turn Control Knob to ÷ and hold knob in.
3 Keep pressing while you turn knob to HI and hold in 5 _ 10
seconds before releasing,
4. If ignition does not occur in 5 seconds, turn gas off at source
and turn Control Knobs OFF Wait at least 5 minutes for gas
to clear, then retry., if your- grill still fails to light turn the
Control Knob(s) and gas source OFF
Wait 5 minutes for
gas to clear and then conduct a leak test as explained in
the LP Gas Tank #]stallation of this guide
if no leaks are
detected, repeat the lighting procedure
5 After Burner is lit, turn the tank valve SLOWLY one more
1/4 of a turn
5 Set Control Knobs to OFF Open Natural Gas valve at
source
if using an LP grill open LP Gas tank valve.
®
.... %7;: - -.
i .....
i j)',)
t
6 Push and turn Right Main Burner Control Knob to _, and
hold in.. You will hear a clicking sound from the elec-
trodes of all burners
Note: Only the burner you are turning on will ignite Once
the burner is lit, turn the knob back to Hi
O
/"__/_
-''¸_¸,¸,
,
7 If ignition does not occur in 5 seconds, turn gas off at source
and turn Control Knobs OFF. Wait at least 5 minutes for gas
to clear, then retry If your grit] still fails to light, turn the burner
Control Knob(s) and gas source OFF Wait 5 minutes for gas
to clear and then conduct a leak test of ALL gas connections
and gas sources as explained in the LP Gas Tank Installa-
tion of this guide
If no leaks are detected, repeat the lighting
procedure.
8 After one Burner is lit, turn the NG valve (or LP tank valve)
SLOWLY one more 1/4 of a turn
9 Turn each other burner knob to _ to light, then back to Ht.
Note: When lighting all three main burners, start with the
burner' furthest from fuel source location, then light remain-
ing burners in sequence moving toward fuel source,
IMPORTANT:
Do not use the Rotisserie Burner and Main
Burners at the same time Rotisserie burner is for Rotisserie
Cooking only
MAIN BURNER
ROTISSERIE
KNOB:
,BURNER KNOB:
INFRARED BURNER
KNOB:
Infrared
Burner
Lighting
Instructions
1 Follow steps 1 through 5 of the Grill Lighting Instructions
2 Push and turn Control Knob to ÷ and hold knob in
3. Keep pressing while you turn knob to Hi and hold in
5 - 10 seconds before releasing
4 If ignition does not occur in 5 seconds, turn gas off at
source and turn Control Knobs OFF. Wait at least 5
minutes for gas to clear, then retry., if your grilt stiII fails to
light turn the Control Knob(s) and gas source OFF Wait
5 minutes for gas to clear and then conduct a leak test as
explained in the NG Installation of lhis guide
If no leaks
are detected, repeat the lighting procedure.
5 After Burner is Iit, turn the NG valve (or LP tank valve)
SLOWLY one more 1/4 of a turn
14
Publicidad
