Publicidad
Idiomas disponibles
Idiomas disponibles
Manually
Lighting
Your Grill By Paper
Match
To light your gas grill by match, insert a match into the Lighting
Stick and follow steps 1 through
5 of the Grill Lighting
Instructions. Then, tight the match and place Lighting Stick
through the Cooking Gdd on the grill as shown below Turn
the nearest Control Knob to the Ht setting to release gas The
Burner should fight immediately
Match
!
k._F (
Lighting
Stick
...........
Never
lean over the grill cooking area while lighting
your gas grill Keep your face and body a safe distance
(at least 18 inches) from the front of grill when lighting
your grill by match.
i
Should
a FLASHBACK
fire occur
in or around the i
Burner Tubes,
follow the instructions below
Failure _
to comply
_th
these
instructions could
result
in a
fire or explosion
that could
cause
serious
bodily
injury,
death,
or property
damage
•
Shut off gas supply to the gas grill
•
Turn the Control Knobs to OFF position,
•
Open the Grill Lid,,
°
Put out any flame with a Class B fire
extinguisher.,
,
Once the grill has cooled down, clean
the Burner Tubes and Burners according
to the cleaning instructions in this Use
and Care Guide.
If ignition does not occur in 5 seconds, turn the Control
Knob(s) and gas source OFF and conduct a leak test
as explained in the Use and Care section of this guide
if no leaks are detected, repeat the lighting procedure.
Troubleshooting
tf the grill fails
to light
:
1 Turn gas off at source and turn Control Knobs to OFF Wait
at least 5 minutes for gas to clear, then retry
2 if your grill still fails to light, check
gas supply and
connections
3 Repeat lighting procedure
If your grill sti!l fails to operate,
turn the gas off at source, turn the Control Knobs to OFF,
then check the following:
[] Misalignment of Burner Tubes over Orifices
Correction:
Reposition Burner Tubes over OriSces
[] Obstruction
in gas line
Correction:
Remove fuel line from grill. Do not smoke! Open
gas supply for one second to clear any obstruction from fuel
line. Close off gas supply at source and reconnect fuel line
to gnll
[] Plugged
Orifice
Correction',
Remove Burners
from grilI by removing the
screw from the rear of each Burner using PhiIlips Head
Screwdriver CarefuUy lift each Burner up and away from gas
valve Orifice. Remove the Orifice from gas valve and gently
clear any obstruction
with a fine wire Then reinstall all
Orifices, Burners, screws and cooking
components
[] If an obstruction is suspected in Gas Valves or Manifold, call
the Grilf Information Center 1-888-317-7642
8am to 8pm
CST, Monday through Friday
[] Obstruction in Burner Tubes
Correction: Foflow the Burner Tube cleaning procedure on
page 20 of this Use and Care Guide
[] Misatignment of Ignitor on Burner
Correction:
Check for proper position of the Electrode Tip
as shown in steps 6 & 7 on page 11. The gap between the
Spark Electrode
Tip and
Spark Receiver
should
be
approximately
3116". Adjust
if necessary
With the gas
supplyclosed, turn anyMain BurnerControl
Knob to _' then
push in and watch for the presence of a spark at the
Electrode.
[] Disconnected
Electric Wires
Correction:
Inspect the Ignitor Junction Box found behind the
Control Panel.. Connect loose Electric wires to Junction Box
and try to light the grill
[] WeakAA battery
Correction:
Unscrew the Ignitor Cap and replace the bat-
tery.
[] If the grill still does not light and you have professionally
converted your grill for LP use, you may need to purge
air from the gas fine or reset the regulator excess gas
flow device Note: This procedure should be done every
time a new LP Gas tank is connected
to your grill
To purge air from your gas line and/or
reset
the regulator
excess
gas flow
device:
[]
Turn Control Knobs to the OFF position
[]
Turn off the gas at the tank valve
[]
For Natural Gas disconnect
regulator
from
12 ft
Natural Gas Hose.
[]
Let unit stand 5 minutes to allow air to purge
[]
For Natural Gas reconnect
regulator
to 12 ft
Natural Gas Hose
[]
For Natural Gas open Shut Off valve
[]
Open the Grill Lid
[]
Push and turn the Riqht Main Burner Control Knob
to _' and you will hear a clicking
sound as the
burner
is being
ignited
[]
Once the burner is lit, turn the knob back to H1
15
Publicidad
