Duty Cycle - ims PRO TIG 200 AC HF FV Manual Del Usuario

Connecting remote/pedal
1- Power up the machine
2- Plug the pedal/remote control to the connecting socket on the machine.
3- The screen will flash and display « No » (Nothing),
4- Select the type of control by turning the intensity adjustment knob:
« No » (Nothing) / « RC »
5- Turn the knob until the desired selecton is reached, and after 2 seconds the display will freeze on the chosen selection.
NB: In case of error, unplug the remote control, ( « No » will be displayed) and re-start the connection
process.
Remark: You will be asked to specify the remote connected each time the machine is powered up.
Functions
Manual remote control (ref.045675):
The remote control enables the variation of current from minimum intensity (DC : 5A / AC : 10 / MMA : 10A) to an
intensity defined by the user.
In this configuration, all modes and functions of the machine are accessible and can be set.
Pedal (ref.045682):
In all modes excluding « Spot » mode, the pedal control enables variation of the current from the minimum intensity
(DC : 5A / AC : 10) to an intensity definied by the user.
In TIG mode, the machine will only operate in two-stage welding (2T mode). The upslope and downslope are not auto-
matic, and are controlled by the User with the foot pedal.
In « Spot » mode, the pedal control replaces the torch trigger (the pedal position has no effect on the current).

DUTY CYCLE

The machine has a specification with a "dropping current output". The duty cycles following the norm EN60974-1 (at
40°C on a 10mn cycle) are indicated in the table below :
TIG 200 AC/DC (230V)/ TIG 200L AC/DC
AC
X% @ I max
13% 200A
60% 95A
100% 80A
Note : The machines' duty cycle has been tested at room temperature (40°C) and has been determined by simulation
SAFETY
Arc welding can be dangerous and can cause serious and even fatal injuries.
Protect yourself and others.
Ensure the following safety precautions are taken:
Arc radiations
Rain, steam, damp
Electric shock
Falls
Burns
Fire risks
Fumes
22
TIG 200 AC/DC HF FV • TIG 200L AC/DC HF
(Remote Control) / « PEd »
DC
X% @ I max X% @
21% 160A 21%
60% 95A 60%
100% 80A 100%
Protect yourself with a helmet fitted with filters in compliance with EN169 or EN 379.
Use your welding unit in a clean/dry environment (pollution factor ≤ 3), on a flat
surface, and more than one meter from the welding work-piece. Do not use in rain or
snow.
This device must only be used with an earthed power supply. Do not touch the parts
under tension. Check that the power supply is suitable for this unit.
Do not move the unit over people or objects.
Wear protective (fire-proof) clothing (cotton, overalls or jeans).
Wear protective gloves and a fire-proof apron.
Ensure other people keep a safe distance from the work area and do not look directly
at the welding arc.
Protect others by installing fire-proof protection walls.
Remove all flammable products from the work area. Do not work in presence of flam-
mable gases.
Do not inhale welding gases and fumes. Use the device in a well ventilated environment,
with artificial extraction if welding indoors.
(Pedal)
I max X% @
160A
20%
95A
60%
80A
100%
TIG 200 AC/DC (110 V)
AC DC
I max X% @ I max
160A 20% 160A
90A 60% 90A
75A 100% 80A
EN
X% @ I max
21% 110A
60% 90A
100% 75A