Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Congratulations on purchasing your TIMEX® watch... Please read these
instructions carefully to understand how to operate your Timex timepiece... Your
watch may not have all of the features described in this booklet...
For more information, please visit: Timex...com
HOW TO START YOUR WATCH
To start your watch remove the plastic guard from under the crown, then press
the crown in against the case... The second hand will begin advancing in one-
second intervals...
Some deep-depth water-resistant watches require the setting crown to be
screwed in to secure water-resistance... If your watch case has a protrusion with
screw threads, the crown must be screwed in after setting the watch...
To screw in, push the crown firmly against the threaded protrusion and hold
in while turning the crown clockwise... Continue to screw in the crown until it is
tight... You will need to unscrew the crown (counter-clockwise) before pulling it
out the next time you want to set your watch...
WATER AND SHOCK RESISTANCE
If your watch is water-resistant, meter marking or (O) is indicated
Water-Resistance Depth
30m/98ft
50m/164ft
100m/328ft
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS UNDER WATER.
1... Watch is water-resistant only as long as crystal, crown and case remain
intact...
2... Watch is not a diver watch and should not be used for diving...
3... Rinse watch with fresh water after exposure to salt water...
4... Shock-resistance will be indicated on the watch face or caseback... Watches
are designed to pass ISO test for shock-resistance... However, care should be
taken to avoid damaging the crystal...
TO SET TIME
1... PULL crown to position C and turn until the hour and minute hands display
the correct time... Note correct time of day (A...M... or P...M...) for proper date
function (if applies)... The date will advance between 9:00 PM and 1:00 AM
2... Push crown to position A...
TO SET DATE (IF APPLIES)
1... PULL crown to position B and turn COUNTER-CLOCKWISE until correct day
appears... Note: if the date is set between the hours of around 9:00 PM and
1:00 AM, the date may not change the following day... If this occurs, reset the
Time and Date at any other time than between the hours of around 9:00 PM
and 1:00 AM to ensure proper date function...
2... Push crown to position A...
p.s.i.a. * Water Pressure Below Surface
60
86
160
DATE
A
B
C
CROWN POSITION
HOW TO ADJUST BRACELET
(Variations of the following bracelet sections apply to all watch models)...
SLIDING CLASP BRACELET
1 Open locking plate...
2... Move clasp to desired bracelet length...
3... Exert pressure while holding locking plate and slide clasp back and forth until
it engages in grooves on underside of bracelet...
4... Press locking plate down until it snaps closed... Clasp can be damaged if
excessive force is used...
FOLDOVER CLASP BRACELET
1... Find spring bar that connects bracelet to clasp...
2... Using a pointed tool, push in spring bar and gently twist bracelet to
disengage...
3... Determine wrist size, then insert spring bar in correct bottom hole...
4... Push down on spring bar, align with top hole and release to lock in place...
Fig. 1
BRACELET LINK REMOVAL
REMOVING LINKS:
1... Place bracelet upright and insert pointed tool in opening of link...
2... Push pin forcefully in direction of arrow until link is detached (pins are
designed to be difficult to remove)...
3... Repeat until desired number of links are removed...
RE-ASSEMBLY:
1... Rejoin bracelet parts...
2... Push pin back into link in opposite direction of arrow...
3... Press pin down securely into bracelet until it is flush...
1
ENGLISH
Fig. 3
Fig. 2
732-096000
Publicidad
Tabla de contenido
