Multi-Purpose Appliance; Replacing Components; Reminders For Replacing Components; Gas Bratt Pan - ALI NBR912E Serie Instrucciones Para Instalación, Uso Y Mantenimiento

• Poor engagement of moving parts (screw nuts, bolt, pins, le-
vers, etc..).
18.3

MULTI-PURPOSE APPLIANCE

The appliance does not heat.
Possible causes:
• Temperature thermostat defective.
• Heating elements defective.
• Safety thermostat tripped.
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.

19 REPLACING COMPONENTS

REMINDERS FOR REPLACING COMPONENTS.

• Disconnect the appliance electric supply, if present, before
carrying out any operation.
• After replacing a gas system component, check for gas leaks
at connection points.
• After replacing an electrical system component, check it is
correctly wired.
19.1

GAS BRATT PAN

Replacing the gas valve, the pilot burner, the thermocou-
ple, the electric ignition and the igniter.
• Remove the front panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the burner.
• Remove the front panel.
• Remove the fixing screws of the front cover.
• Fully lift the pan and unscrew the central fixing screw of the
burner.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the temperature thermostat, the control knob,
the indicator lamp and the safety thermostat
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Pan lifting microswitch
• Remove the front panel.
• Disconnect the device's electrical connections.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Pan movement motor
• Remove the front panel.
• Lower the well completely.
• Disconnect the device's electrical connections.
• Detach the connection with the pan lifting "bolt".
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
40
Screw nuts and manual pan movement system (bolt)
• Remove the front panel.
• Lift the pan completely, locking it firmly in that position
(e.g.with a bar). Important:measure how far tightened the
"bolt" is with regard to the screw nut before removing the
components.
• Disconnect the "bolt" from the handwheel shaft.
• Undo the screw nut fixings.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
19.2

ELECTRIC BRATT PAN

Replacing the heating element
• Lift the pan completely, locking it firmly in that position
(e.g.with a bar).
• Remove the guard from the element.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the temperature thermostat, the control knob,
the indicator lamp and the safety thermostat
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Pan lifting microswitch
• Remove the front panel.
• Disconnect the device's electrical connections.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Pan movement motor
• Remove the front panel.
• Lower the well completely.
• Disconnect the device's electrical connections.
• Detach the connection with the pan lifting "bolt".
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Screw nuts and manual pan movement system (bolt)
• Remove the front panel.
• Lift the pan completely, locking it firmly in that position
(e.g.with a bar). Important:measure how far tightened the
"bolt" is with regard to the screw nut before removing the
components.
• Disconnect the "bolt" from the handwheel shaft.
• Undo the screw nut fixings.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
19.3 MULTI-PURPOSE APPLIANCE
Replacing the heating element and the indicator light
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the working thermostat and safety thermostat
• Remove the control panel.