Vimar ELVOX 6900 Serie Instrucciones página 16

6900
Table of primary and respective secondary ID codes:
Primary Secondary ID
ID
1 2 3
1 51 52 53
2 54 55 56
3 57 58 59
4 60 61 62
5 63 64 65
6 66 67 68
7 69 70 71
8 72 73 74
9 75 76 77
10 78 79 80
11 81 82 83
12 84 85 86
13 87 88 89
14 90 91 92
15 93 94 95
16 96 97 98
17 99 100 101
18 102 103 104
19 105 106 107
20 108 109 110
21 111 112 113
22 114 115 116
23 117 118 119
24 120 121 122
25 123 124 125
Important: Delete from Group: to delete from a group, the
programming deletion procedure described in the "Deleting
programming" section must be carried out (all programming
deleted).
Button programming
Important: without programmer 950C or SaveProg software,
the only functions that can be assigned are intercommunica-
ting, specific entrance panel self-activation, restoring buttons
programmed by the installer to their default settings and dele-
ting all programming procedures performed.
E1 E2
D
C
16
Primary Secondary ID
ID
1 2
26 126 127
27 129 130
28 132 133
29 135 136
30 138 139
31 141 142
32 144 145
33 147 148
34 150 151
35 153 154
36 156 157
37 159 160
38 162 163
39 165 166
40 168 169
41 171 172
42 174 175
43 177 178
44 180 181
45 183 184
46 186 187
47 189 190
48 192 193
49 195 196
50 198 199
E4 E5
E3 E6
Programming intercommunicating call buttons
To program the buttons, proceed as follows:
1) Press "speak/listen" or lift the handset (depending on the
model installed) of the interphone you wish TO CALL.
3
2) Press and hold button B on the interphone you wish to
128
program (making the call).
131
3) Press and hold button A at the same time.
134
4) Wait for the RED LED to flash.
137
5) Release buttons A and B.
140
6) Press and hold the button you wish to program (e.g. E1, E2,
143
E3, E4, E5, E6).
146
7) Wait for the interphone to emit a chime.
149
8) Release the button you wish to program on the interphone
152
making the call.
155
9) Press a button (lock/F1/F2) on the interphone you wish
158
to call.
161
10) A "note" on the interphone (making the call) being pro-
164
grammed confirms the setting has been saved.
167
170 Important: This procedure can be used to manually repro-
gram the buttons, with the exception of the speak/listen button
173
(not programmable) and the lock and self-start buttons (for
176
which programmer 950C or SaveProg software is required).
179
182
Programming the self-activation/self-start button
185
188 to a specific panel
191
(different from the self-start function enabled using button
194
"A")
197
1) Press and hold button B.
200
2) Press and hold button A at the same time.
3) Wait for the RED LED to flash.
4) Release buttons A and B.
5) Press and hold the button you wish to program (excluding
speak/listen, lock and self-start).
6) Wait for the interphone to emit a tone.
7) Release the button.
8) For entrance panels with buttons, press the button corre-
sponding to the monitor on which the button is being saved.
For alphanumeric entrance panels, enter the ID number
corresponding to the monitor on which the button is being
saved, and confirm using the bell button on the entrance
panel.
9) At the end of the procedure described above, a sharp tone
will be emitted by the interphone, while the entrance panel
makes a call to the interphone on which programming has
taken place.
Reprogramming the default value separately for
each button
A
1) Press and hold button B.
2) Press and hold button A at the same time.
B
3) Wait for the red LED to flash.
4) Release buttons A and B.
5) Press and hold the button for which you wish to restore
the default setting (does not apply to Self-start and Lock
buttons).
6) Wait for the interphone to emit a tone.
7) Release the button.
8) Press the button again (it will now be restored to its default
value).
EN