Service; Emissions; Safety Symbol Explanations; Additional Safety Note - Wyco SureSpeed Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Safety Symbol Explanations

Service

Have your power tool serviced by a qualified repair person
using only identical replacement parts to ensure the tool is
safe to use

Emissions

1 Declared noise emission values:
K = 0 69 dB
L
= 83 1 dB
pA
L
= 94 1 dB
WA
N
OTEE:
Wear hearing protection
2 Declared vibrator emissions:
Front Handle = 4 28 m/s
K = 1 50 m/s
Rear Handle = 2 41 m/s
K = 1 50 m/s
N
OTEE:
The declared vibration total value has been
measured in accordance with a standard test
method and may be used for comparing one tool
with another The declared vibration total value may
also be used in a primary assessment of exposure
WARNING
THE VIBRATION EMISSION DURING ACTUAL USE OF THE
POWER TOOL CAN DIFFER FROM THE DECLARED TOTAL
VALUE DEPENDING ON THE WAYS IN WHICH THE TOOL IS
USED.
SAFETY SYMBOL EXPLANATIONS
V
Volts
A
Amperes
Hz
Hertz
Alternating Current
Class II Tool
IPX4
IP Symbol
Ground Terminal (Protective Earthing)
ON
OFF
Refer to Instruction Manual
Variability in Steps
Figure 1: Safety symbols
Page 6
2
2
2
2

Additional Safety Note

Double insulated tools are equipped with a polarized plug
(one blade is wider than the other) This plug will fit in a
polarized outlet only one way If the plug does not fit fully
in the outlet, reverse the plug If it still does not fit, contact
a qualified electrician to install a polarized outlet Do not
change the plug in any way Double insulation eliminates the
need for the three-wire grounded power cord and grounded
power supply system

INTRODUCTION

This concrete vibrator motor is used to power concrete flex
shaft vibrators which provide vibration to consolidate freshly
poured concrete The vibration is created by an eccentric (off
center) weight within the vibrator head As the weight spins
it forces the head housing to move within the fresh concrete
The continuous head movement agitates the concrete
mixture resulting in significantly reduced voids
This motor can be used with any valid Wyco vibrator
head and shaft combination See
combinations Shafts are available in lengths of 2, 5, 7, 10, 14,
20 and 30 feet (0 61, 1 52, 2 13, 3 05, 4 27, 6 1, and 9 14 m)
WARNING
DO NOT USE NON-APPROVED PARTS. THE USE OF
NON-APPROVED PARTS MAY CAUSE A HAZARDOUS
CONDITION FOR THE OPERATOR.
Vibrator Head
Size in.
(mm)
13/16 (4 76)
1 (25 4)
1-3/8 (34 92)
1-3/4 (44 45)
2 (50 8)
2-1/4 (57 15)
2-1/2 (63 5)
1-3/8 (34 92)
Table 1: Wyco head and shaft combinations
I
MPORTANT
Third party approvals/certifications only apply when Product
is used solely with head and shaft models listed in Product's
user manual.
VBR-UM-00043-EN-06
Table 1
for common
Vibrator Shaft
Model No
Length
750-D
2...20 ft
(0 61...6 1 m)
750-EH
750-FI
750-GI
2...20 ft
750-LI
(0 61...6 1 m)
750-MI
750-SBI
30 ft
750-FI
(9 14 m)
CK Series
8900
9500
December 2018

Publicidad

Tabla de contenido
loading

Productos relacionados para Wyco SureSpeed

Este manual también es adecuado para:

994

Tabla de contenido