Carol™ Ts; Carol™ Mo; Scafor™ R; Installation - Tractel blocfor Serie Manual De Instalación, De Utilización Y De Mantenimiento

Use in load lifting
The caRol™ R winch is a load lifting winch in
accordance with Directive 2006/42/EC with a max. WLL
of 250 kg. Its lifting function allows the operator to raise
and/or lower a max. load of 250 kg.
4.2.2. caRol™ TS
The caRol™ TS winch is a load lifting winch in
accordance with Directive 2006/42/EC with a max. WLL
of 500 kg. Its lifting function allows the operator to raise
and/or lower a max. load of 500 kg.
4.2.3. caRol™ MO
The caRol™ MO winch is a motorised load lifting winch
in accordance with Directive 2006/42/EC with a max.
WLL of 500 kg. Its lifting function allows the operator to
raise and/or lower a max. load of 500 kg.
When using for rope access, only one operator can be
connected to the caRol™ MO winch. It must always be
connected to a fall arrester with a recovery function.
See the caRol™ MO manual.
4.3. scafor™ R
The scafor™ davitrac bracket can be used to attach a
scafor™ winch.
Usage in rescue lifting
The scafor™ R winch is a winch which is an EN 1496
lifting rescue device. In this configuration, its maximum
capacity is 150 kg. Its recovery function allows the
rescuer to raise and/or lower the operator after a fall.
Use in load lifting
The scafor™ R winch is a load lifting winch in
accordance with Directive 2006/42/EC with a max. WLL
of 500 kg. Its lifting function allows the operator to raise
and/or lower a max. load of 500 kg.

5. Installation

For information on how to use the systems attached
to the brackets, see the manuals supplied with each
system.
Before positioning the davitrac bracket on the mast of
the davitrac, the operator must ensure that the mast
is placed correctly on its base and that the base is
securely attached to the structure in accordance with
the davitrac base instructions.
The davitrac anchor bracket may only be fitted on the
mast of the davitrac.
They are equipped with keying devices designed to
position the bracket at the top or bottom of the davitrac
mast.
The davitrac brackets are equipped with locking pins
with a safety pin, connected by a steel cablet.
When only one system is installed, it must be installed
at the rear of the mast:
• A scafor™ R or caRol™ winch is placed in the
high position (fig. 3.a); and
• The blocfor™ R fall-arrest device is in the low
position (fig. 3.b).
When several systems are installed, they must be
installed as follows:
• A scafor™ R or caRol™ winch is placed in the
high position at the rear of the mast (fig. 3.c); and
• The blocfor™ R fall-arrest device is in the low
position at the front of the mast (fig. 3.c).
No other configuration is permitted.
Depending on the positioning of your system, route
the cable over the transfer pulleys (fig. 3). For front-
mounted equipment, the cable should pass over the
front pulley. For rear-mounted equipment, the cable
should pass over the rear pulley.
The position of the anchor head can be set to three
positions as required. Always lock it into position with
its safety pin.
NOTE: No other assembly than those set out
above is permitted without the written approval of
Tractel .
®
NOTE: The stated loads are the maximum
values applicable, which must not in any event be
multiplied by the number or anchor points located on
the head or mast of davitrac.
5.1. blocfor™ 20R and 30R
Before using blocfor™ 20R or 30R for the first time, it
needs to be installed on its bracket provided for this
purpose.
5.1.1. Installation of the blocfor™ 20R and 30R on
the blocfor™ davitrac bracket
1. Position the blocfor™ anchor point on the bracket
anchor point (fig. 4.a), and position the washer and
locknut without tightening them.
2. Place the flat-angle bracket on the cable tray of the
blocfor™ bracket and adjust it. Then put in place its
mounting screw.
3. Tighten the locknut firmly (fig. 4.a) and tighten the
screw of the flat-angle bracket (fig. 4.a).
GB
9