Machine Care; Machine Maintenance; Machine Storage - Bissell HYDROCLEAN PROHEAT COMPLETE 1474J Guia Del Usuario

D
Care,
Maintenance & Storage
D-1 Machine Care
1. Push Power and Wet Clean Buttons OFF.
Unplug cleaner.
2. Open Quick Release™ Hose Door and
remove Collection Tank by lifting straight up
using tank handle.
3. Remove top lid from Collection Tank, rinse
and air dry.
4. Empty dirty water into a sink, toilet
or outside by pouring dirt water out
from corner of tank. Rinse inside of Collection
Tank.
5. Remove Cleaning Mode Selector by turning
to "REMOVE" and pulling straight out.
6. Once Cleaning Mode Selector is removed,
remove water filtration tower by lifting up and
rotating clockwise so front of tower is facing
side of Collection Tank. Then pull up and out
of Collection Tank.
7. Rinse Collection Tank, Cleaning Mode
Selector and water filtration tower. Allow
to air dry completely before replacing
water filtration tower and cleaning mode
selector back into Collection Tank.
a. To replace filtration tower back
into Collection Tank, drop into top of
Collection Tank and rotate counter-
clockwise so front of tower is facing front
of Collection Tank. Be sure to align with
tabs in bottom of Collection Tank.
b. Once water filtration tower is replaced,
replace Cleaning Mode Selector by
inserting back into front of cleaner.
Make sure cleaning mode selector is in
"REMOVE" position when inserting back
into cleaner. Turn either clockwise to
"FILTER VAC" or counter-clockwise to
"WET CLEAN" to lock back in place.
8. For wet cleaning, remove all tools that
were used and rinse with clean tap water.
Allow to dry completely before storing.
9. The nozzle on the carpet deep cleaning
tool can be removed for a more thorough
clean.
a. Using a Phillips-head screwdriver,
remove four screws from back side of
tool. Separate clear front nozzle from
back side of tool and rinse both parts
clean with running tap water. Allow to air
dry completely before reassembling.
10
b. To reassemble, place clear front nozzle
on to back side of tool by mating cut out
area at top of nozzle to black tool holder,
located on front top of back side of tool.
Press bottom of nozzle so four screw
bossed insert into screw holes in back
tool holder. Replace four screws on back
side of tool. Note: two long screws go
into screw holes at bottom of tool near
brushes.
10. Remove hose and Solution Hose, taking
care to keep both ends of hose up to avoid
spilling any residual water. Empty out any
residual water in a sink water and rinse clean
with running tap water. Allow to air dry
completely before storing or placing back on
cleaner.
D-2 Machine Maintenance
1. Pre-Motor Filter: Remove from top lid
by pulling tab away from separator and
pulling straight out. Remove foam filter from
separator and inspect. If dirty, rinse with clean
tap water and allow to air dry completely
before replacing back into separator. To
attach separator back onto to top lid, line up
"T" pieces under shallow grooves on top lid
and push together until tab clicks together.
2. Post-Motor Filter: Open filter door by
pressing down on latch and pulling down.
Once filter door is open, place one hand
on each side of filter and pull it out of
machine. If dirty, replace with new filter or
rinse under clean tap water and allow to air
dry completely before replacing back into
machine. Be sure filter door is fully closed and
latched prior to operating machine.
D-3 Machine Storage
Water and cleaning formula can be left
in Solution Tank for next use.
1. Pull Quick Release cable wrap to left to
extend and wrap Power Cable.
2. Store unit in a protected, dry area, at
room temperature (4° to 43° C).
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
ALWAYS INSTALL FLOAT BEFORE ANY WET PICK-UP
OPERATION.
NOTICE
TO REDUCE THE RISK OF A LEAKING CONDITION,
DO NOT STORE UNIT WHERE FREEZING MAY OCCUR.
DAMAGE TO INTERNAL COMPONENTS MAY RESULT.