Toshiba MMY-MAP0804HT5P Manual De Instalación página 18

Table 2
Combined HP (HP)
8 8HP
10 10HP
12 12HP
14 14HP
16 16HP
18 10HP
20 10HP
22 12HP
24 12HP
26 16HP
Standard type 28 16HP
30 16HP
32 16HP
34 12HP
36 12HP
38 16HP
40 16HP
42 16HP
44 16HP
46 16HP
48 16HP
16 8HP
24 8HP
26 10HP
28 10HP
30 10HP
32 8HP
34 10HP
High Efficiency type
36 10HP
38 10HP
40 10HP
42 12HP
44 12HP
46 12HP
48 12HP
Charging of refrigerant
Keeping the valve of the outdoor unit closed, be sure to charge the liquid refrigerant into the service port at the
liquid side.
If the specified amount of refrigerant cannot be charged, fully open the valves of the outdoor unit at liquid and
gas sides, operate the air conditioner in COOL mode, and then charge refrigerant into service port at the gas
side. In this time, choke the refrigerant slightly by operating the valve of the canister to charge liquid refrigerant.
The liquid refrigerant may be charged suddenly, therefore be sure to charge refrigerant gradually.
33-EN
1114208701-1 EN PT ES.indb 17 1114208701-1 EN PT ES.indb 17
C (Corrective amount
Combined outdoor units (HP)
of refrigerant) (kg)
– – – 1.5
– – – 2.5
– – – 3.5
– – – 8.5
– – – 10.5
8HP – – 0.0
10HP – – 3.0
10HP – – 5.0
12HP – – 7.5
10HP – – 8.5
12HP – – 9.5
14HP – – 11.5
16HP – – 12.5
12HP 10HP – 3.0
12HP 12HP – 4.0
12HP 10HP – 6.0
12HP 12HP – 7.0
14HP 12HP – 8.0
16HP 12HP – 10.0
16HP 14HP – 12.0
16HP 16HP – 14.0
8HP – – 0.0
8HP 8HP – -4.0
8HP 8HP – -4.0
10HP 8HP – -2.0
10HP 10HP – 0.0
8HP 8HP 8HP -6.0
8HP 8HP 8HP -6.0
10HP 8HP 8HP -6.0
10HP 10HP 8HP -6.0
10HP 10HP 10HP -5.0
10HP 10HP 10HP -4.0
12HP 10HP 10HP -2.0
12HP 12HP 10HP 0.0
12HP 12HP 12HP 2.0
– 17 –
Full opening of the valve
Open the valves of the outdoor unit fully.
MAP080
MAP100
MAP120
Packed valve
Using a 4mm-hexagonal wrench,
fully open the valve rods.
Liquid side
Balance packed valve
Balance pipe
Using a 4mm-hexagonal wrench, fully open the valve rods.
Ball valve
Using a wrench, turn it counterclockwise by 90° until it hits the stopper.
(Full open)
Gas side
MAP140
MAP160
Ball valve
Using a flathead screwdriver, turn it counterclockwise by 90° until it hits the
stopper. (Full open)
Position of screwdriver slot
Service
port Valve unit
Fully closed Fully opened
Using flathead
screwdriver, turn it
counterclockwise by
90° until it hits the
(1)
stopper. (Full open)
Slot
(2)
Flare nut
*
When opened fully, do not apply
excessive torque after the screwdriver hits
the stopper; otherwise a problem may be
caused on the valve. (5
Fully opened
Fully closed
or less)
34-EN
02/27/14 1:39 PM 02/27/14 1:39 PM