Moretti LEM Aspimed 2.2 Manual De Instrucciones página 14

The surgical aspirator ASPIMED 2.2 is intended for use in the electromagnetic environment specified below.
The customers or the user of the surgical aspirator ASPIMED 2.2 should assure that it's used in such an environment.
Immunity Test
Conducted Immunity
IEC / EN 61000-4-6
Radiated Immunity
IEC / EN 61000-4-3
Note 1: At 80 MHz and 800 MHz the interval with the highest frequency is applied
Note 2: These guide lines may not be applicable in all situations. The electro-magnetic propagation is influenced by the absorption
and by reflection from buildings, objects and people.
a) The field intensity for fixed transmitters such as the base stations for radiotelephones (mobile and cordless) and terrestrial mobile
radio, amateur radio devices, radio AM and FM transmitters and TV transmitters can not be theoretically and accurately foreseen.
To establish an electro-magnetic environment generated by fixed RF transmitters, an electro-magnetic study of the site should be
considered. If the field intensity measured in the place where the device will be used surpasses the above mentioned applicable level
of conformity, the normal functioning of the device should be monitored. If abnormal performance arises, additional measures such
as changing the device's direction or positioning may be necessary.
b) The field intensity on an interval frequency of 150 kHz to 80 MHz should be less than 3 V/m.
Recommended separation distance between portable and mobile radio-communication devices and the monitor
The ASPIMED 2.2 surgical aspirator is intended to operate in an electro-magnetic environment where RF irradiated interferences are
under control. The client or operator of the ASPIMED 2.2 device can help prevent electro-magnetic interference by keeping a
minimum distance between the portable and mobile RF communication devices (transmitters) and the ASPIMED 2.2 device, as
recommended below, in relation to the radio-communication maximum output power.
Maximum nominal
output power of the
Transmitter W
0,01
0,1
1
10
100
For transmitters with a maximum nominal output power not shown above, the recommended separation distance in metres (m) can
be calculated using the equation applicable to the transmitter frequency, where P is the maximum nominal output power of the
transmitter in Watt (W) depending on the transmitter's manufacturer.
Note 1: At 80 MHz and 800 MHz the interval with the highest frequency is applied
Note 2: These guide lines may not be applicable in all situations. The electro-magnetic propagation is influenced by the absorption
and by the reflection from buildings, objects and people.
Guidance and manufacturer's declaration – Immunity Emissions
Level indicated by the
IEC 60601-1-2
3Vrms 150kHz to
80Mhz
(for non life-supporting
devices)
3V/m 80MHz to 2.5GHz
(for non life-supporting
devices)
Separation distance from the frequency transmitter (m)
150 kHz to 80 MHz
d = [3.5 / V ]
P
1
0,12
0,38
1,2
3,8
12
Compliance Level
V = 3 V rms The portable and mobile RF communication
1
devices, including cables, must not be used closer
to the ASPIMED 2.2 device, than the separation
distance calculated by the equation applicable to
the transmitter frequency. Recommended
E = 3 V / m
1
separation distance
d = [3.5 / V
d = [12 / E
d = [23 / E
Where P is the maximum nominal output voltage of
the transmitter in Watt (W) depending on the
manufacturer of the transmitter and the
recommended separation distance in metres (m).
The intensity of the field from the fixed RF
transmitters, as determined by an electro-magnetic
study of the site
conformity of each frequency interval
It is possible to check for interference in proximity
to devices identified by the following symbol:
80 MHz to 800 MHz
d = [12/E ]
P
1
0,12
0,38
1,2
3,8
12
14
Electromagnetic environment - guidance
]
P
1
P
] from 80 MHz to 800MHz
1
P
] from 800 MHz to 2.5 GHz
1
a)
, could be lower than the level of
800 MHz to 2.5 GHz
d = [23/E
0,23
0,73
2,3
7,3
23
b)
.
] P
1