Publicidad
Idiomas disponibles
Idiomas disponibles
5.16 - Adjustment of "Sun" climate sensor (ref. paragraph 6.2.3)
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps.
Before starting the procedure, move the shutter/awning to the mid-point of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the t key a few times, depending on the level you want to set for the intervention threshold:
1 press = 5 Klux
2 presses = 10 Klux
3 presses = 15 Klux (factory setting)*
4 presses = 30 Klux
5 presses = 45 Klux
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the proce-
dure. this way, the adjustment is completed without changing the factory setting.
04. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
01
5
sec.
03
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux (*)
0,5
x 4 = 30 Klux
sec.
x 5 = 45 Klux
Note: • When performing the procedure, you can cancel it at any time by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements. • If you use a sensor equipped with a "trimmer", you must read the sensor instructions and ad-
just the threshold directly on the sensor.
––– Procedure 5.16 ––– executable only with a series transmitter Era P and Era W
01
PRG
1
sec.
04
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux ( * )
0,5
x 4 = 30 Klux
sec.
x 5 = 45 Klux
(*) - Factory setting
5.17 - Adjustment of "Wind" climate sensor (ref. paragraph 6.2.3)
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps.
Before starting the procedure, move the shutter/awning to the mid-point of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the s key a few times, depending on the level you want to set for wind threshold:
1 press = wind at 5 Km/h
2 presses = wind at 10 Km/h
3 presses = wind at 15 Km/h (factory settings)*
4 presses = wind at 30 Km/h
5 presses = wind at 45 Km/h
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the proce-
dure. this way, the adjustment is completed without changing the factory setting.
04. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
02
2
10
?
sec.
02
PRG
1
2
sec.
10
?
sec.
5
3
sec.
04
1 /
2 /
3 /
5
4 /
sec.
5 /
03
5
2
sec.
05
1 /
2 /
3 /
5
4 /
3
sec.
5 /
3
3
English – 13
Publicidad
