Basic Operation - Denon DN-S3000 Instrucciones De Operación

BASIC OPERATION

5
Play and pause
• Each push of the i PLAY/PAUSE (
13 ) button
switches between playback and pause.
PLAY/PAUSE ( 13 ) button illuminates solid green
during playback and flashed in pause.
• When the i PLAY/PAUSE (
13 ) button is pushed
during play, the DN-S3000 pauses playback at that
point. Push i PLAY/PAUSE (
13 ) button once
again and playback resumes.
• When the Scratch mode is set to MAIN, the Platter
turns when the Main Track is played. When the
rotation of Scratch Disc is stopped by pressing with
the finger, the pause mode is set, and when the
finger is released playback resumes.
NOTE:
Standing up of playback
slows unusually after trans
porting the product.At the
time, push center of the !1
Scratch Disc lightly.
Play and Cue
• When the !0 CUE button is pushed during playback,
the track stops and returns to the position that
current playback started (Cue point) and prepares
for next playback. This function is called Back-Cue.
With Back-Cue function, you can start from exactly
same position. The !0 CUE button illuminates solid
red when DN-S3000 is ready to start playback.
• You can set and change Cue point as follows.
• When you started playback.
• Track select finished.
• manual search.
!
Move the Cue point
• If you would not like to start playback from
beginning of the track, you need to move Cue Point
using fast Search and manual search function.
You can move to the approximate playback
start position by #1 or #2 FAST SEARCH
buttons.
[1-MIN.SKIP]
• If the FAST SEARCH button
is pushed short time, the
1
playback position skips for about 1 minute.
[FAST SEARCH]
• When the FAST SEARCH button is pressed
and held in, the disc is fast-searched.
Push the @9 SCRATCH
MODE button for more than
1 sec to set @9 Scratch Disc
2
to search mode. The
SCRATCH MODE button
LEDs will turn off.
Turn the !1 Scratch Disc to
change Cue point. You can hear
the short sound of the current
3 Cue point.
When !1 Scratch Disc is turned in the pause,
standby or frame repeat mode, works as the
manual search function.
After you found your
preferred Cue point, push
4
the !0 CUE button then new
Cue point is set.
Adjusting the pitch
• With Pitch slider you can adjust the playback speed
(Pitch).
• If you would not prefer to change key of sound, use
the Key Adjust function.
Push the #6
PITCH/KEY
button to PITCH LED lights up.
1
• PITCH → KEY (key adjust) → OFF
Pitch decreases
Move the #5 Pitch slider to adjust
the pitch. The current pitch setting
2
is displayed on the display.
Pitch increases
DN-S3000 has five pitch ranges,
4%, 10%, 16%, 24% 50% and
100%. When the #6
RANGE
3
button is pushed for more than 1
sec, the pitch range can be
selected with the #0
PARAMETERS knob.
Pitch Bend
• With PITCH BEND function you can change pitch
temporary. DN-S3000 has three ways for this
function PITCH BEND buttons and Scratch Disc.
[PITCH BEND +/– buttons]
• Push the #3 PITCH BEND
– or #4 + button for
PITCH BEND
momentary change of
1
pitch.
While holding these buttons down, the pitch
continues to change up to the limitation.
• After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
When the Scratch source is
set to MAIN and the Platter is
turning, playback of the Main
source can be slowed
temporarily by lightly pressing
2
!1 Scratch Disc or PLATTER.
In addition, playback can be quickened
temporarily by pushing Scratch Disc or
PLATTER in the direction in which the Platter
is turning.
[Scratch Disc]
• When the Scratch mode is
set to SEARCH, the playback
speed can be changed by
turning !1 Scratch Disc
3
during playback.
• The pitch increases gradually when the
Scratch Disc is turned clockwise and
decreases when turned counterclockwise.
• When you stop turning the Scratch Disc, the
playing speed returns to the previous pitch.
Select the track
• Turn the #0 TRACK knob.
• By pushing #0 TRACK knob down while turning, the
tracks will change 10 at a time.
ENGLISH
Relay playback
• Relay Play function is a playback mode to continue
play tracks of CDs in two DN-S3000s.
• Connect the X-EFFECT IN/OUT terminals between
two DN-S3000s.
q, w
Start Relay Play
q Push the RELAY button
for more than 1 sec to
enable Relay play mode.
You can set Relay mode
as below.
• In the single play mode, when the one
player's playback reaches end of track,
another DN-S3000 starts playing.
1
• In the continuous play mode, when the
whole tracks on one side are finished,
another DN-S3000 starts.
• The discs in two DN-S3000s can be
played alternately by setting both DN-
S3000 to the relay play mode.
• Relay play can be set in the program and
random play modes.
• Relay play is possible also for DN-S3000
or DN-S5000.
Stop Relay Play
w When the RELAY button
is pushed for more than 1
2
sec while in the relay play
mode, the relay play
mode is turned off.
Power on play
• When "POWER ON PLAY" is set to "ON" at "⁄4
PRESET (8)", playback starts from the first track on
the disc when the power is turned on.
11