Publicidad
Notes:
-
Higher than normal current readings indicate short circuit faults.
Lower than normal current readings with the same voltage
readings will most probably indicate arcing faults, a poor
connection or broken wire.
-
On an earth-wire-return fence, readings taken on the earth wire
may not indicate the correct current direction.
Live fence alert tone
When the fence wire is in the Fence wire voltage slot or the Fence wire
remote slot, the Remote Control Handset beeps each time the
energizer pulses to indicate that the fence is live. The pitch of the alert
tone rises with the magnitude of the current pulse. This is particularly
useful when measuring currents in different branches at a junction
point, and when the display cannot be seen. If the power supply to the
fence has been switched off, the Remote Control Handset will not beep.
Enabling and disabling live fence alert tone
1
Press and hold
, then press
2
Press
once to scroll to the flashing note ( ).
a toggle to switch the alert tone on or off.
3
Do one of the following:
- To enable the live fence alert tone, press
on the screen.
- To disable the live fence alert tone, press
on the screen.
4
Press
to move to the next setting.
5
Press
to switch off the Remote Control Handset.
Backlight
The remote control has a backlight for better screen visibility when
there is not enough daylight. If required, this feature can be turned off
to conserve battery life.
Enabling and disabling the backlight
1
Press and hold
, then press
2
The backlight option will now be flashing (bL).
toggle to switch the backlight on or off.
3
Do one of the following:
- To enable the backlight, press
screen.
- To disable the backlight, press
screen.
4
Press
to move to the next setting.
5
Press
to switch off the Remote Control Handset.
Battery
The remote control battery must be replaced when you see the
symbol on the screen.
To replace the battery:
1
Unscrew the case back.
2
Unclip the old battery, and replace with a new PP3, 9 V, alkaline
battery.
3
Screw the case back into place, taking care not to trap the battery
leads under the screws or in the case assembly.
4
to enter the Set-up mode.
now acts as
until ON appears
until OFF appears
to enter the Set-up mode.
now acts as a
until ON appears on the
until OFF appears on the
Caring for the Remote Control Handset
Do not leave the Remote Control Handset in direct sunlight, for
•
instance on a vehicle dashboard.
Use only a damp cloth to clean the remote control.
•
If the Remote Control Handset gets wet, wipe it dry and place it
•
face down to allow any water to run out of the speaker grill. The
Remote Control Handset is water-resistant and should require no
further attention.
Communication between the energizer
and a Remote Control Handset
Understanding address settings
The energizer communicates with a Remote Control Handset using a
channel. The channel has a unique address setting.
An energizer supplied with a Remote Control Handset has its address
preset to one of 16 possible addresses. The Remote Control Handset is
configured to match it.
An energizer supplied without a Remote Control Handset has its
address preset to 0 (zero). This means that it will not recognise or act
on commands from a remote control.
You may want to change the address setting of your energizer:
If you buy a Remote Control Handset separately and you want to
•
configure your energizer to accept commands from it.
If you are using more than one remote-controlled energizer on
•
your property and you want each remote control to operate one
energizer only.
If an adjacent property has an energizer that is operating at the
•
same address setting.
If your energizer turns off unexpectedly quite often.
•
A different address setting for each energizer prevents unintentional
activation or deactivation of fence lines.
Reading the energizer's address setting
When first connected to the power source, all light segments on the
LED display illuminate. They then illuminate separately from left to right
and back again. This indicates that the energizer is operating normally.
The LED display then displays a light sequence, for three seconds, that
identifies the address setting of the energizer.
To identify your energizer's address setting, match the illustration with
what you see on the display.
Address
1
2
3
4
5
6
7
8
9
10
11
12
Publicidad
