Ht 40 Flexx Handheld Transmitter; Controls; Pt 40 Flexx Bodypack Transmitter - AKG Acoustics WMS 40 PRO FLEXX Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 41
WMS 40 FLEXX_5.0_neu
02.05.2005
11 AUDIO OUT/UNBALANCED: Unbalanced audio output on a 1/4" TS jack for connecting to, e.g., a
guitar amplifier.
12 Strain relief for the feeder cable of the supplied AC adapter.
13 DC ONLY: Input connector for the supplied AC adapter.
14 SQUELCH: The squelch circuit switches the receiver off if the received signal is too weak, in order to
suppress the related noise or the residual noise of the receiver while the transmitter is off. Set the
SQUELCH control to minimum before first switching the receiver on.
Operating in the 660 MHz to 865 MHz UHF range, the HT 40 FLEXX provides three selectable, quartz sta-
bilized carrier frequencies within the 3-MHz-wide frequency band for which you ordered your WMS 40
FLEXX. The antenna is integrated in the body.
The microphone element permanently mounted on the transmitter uses a high quality cardioid transduc-
er from AKG. It provides low handling noise sensitivity, high gain before feedback, and brilliant sound
quality, as well as a built-in wind and pop filter to reduce wind and breath noise.
15 On/off switch: This slide switch provides three positions:
ON: Power to the transmitter is on.
MUTE: The signal delivered by the microphone element is muted while power and the RF carrier fre-
quency remain on.
OFF: Power to the transmitter is off.
16 Status LED: Indicates the transmitter's operating status.
LED lit green: Battery is OK.
LED lit red: From the moment the LED changes to red, the battery capacity will provide a maximum
of two operating hours. We recommend replacing the battery with a new one as soon as possible.
If you use a rechargeable battery, the LED will change to red 15 minutes before the battery will be
dead!
17 Frequency selector: This slide switch tunes the transmitter to one of three different carrier frequen-
cies within the transmitter's carrier frequency band.
18 GAIN: This slide switch sets the transmitter's audio input gain in two stages, "HIGH" (high gain) or
"LOW" (low gain).
19 Color code clip: The color of this plastic clip indicates the carrier frequency band of your transmitter.
Receivers tuned to the same frequency band are marked with the same color. Refer to the Manual
Supplement sheet for a color code table.
You can remove the color code clip on the HT 40 FLEXX and replace it with the supplied semitrans-
parent clip.
20 Battery compartment lid: Refer to section 3.5.
21 Carrier frequency label: The label above the battery compartment indicates the name of the carrier
frequency band and the three carrier frequencies of your transmitter.
You can use the PT 40 FLEXX bodypack transmitter with both dynamic microphones and condenser
microphones operating on a supply voltage of approx. 4 V. You may also connect an electric guitar, elec-
tric bass, or remote keyboard.
Operating in the 660 MHz to 865 MHz UHF range, the HT 40 FLEXX provides three selectable, quartz sta-
bilized carrier frequencies within the 3-MHz-wide frequency band for which you ordered your WMS 40
FLEXX.
22 On/off switch: This slide switch provides three positions:
ON: Power to the transmitter is on.
MUTE: The signal delivered by the microphone element is muted while power and the RF carrier fre-
quency remain on.
OFF: Power to the transmitter is off.
23 Status LED: Indicates the transmitter's operating status.
LED lit green: Battery is OK.
LED lit red: From the moment the LED changes to red, the battery capacity will provide a maximum
of two operating hours. We recommend replacing the battery with a new one as soon as possible.
If you use a rechargeable battery, the LED will change to red 15 minutes before the battery will be
dead!
24 Audio input: 3-pin mini XLR connector with both mic and line level pins that automatically match the
connector pinout of the recommended AKG microphones or MKG L guitar cable.
While the MKG L guitar cable is included in the Instrumental Set (see section 2.2 Unpacking), it is also
available as an optional accessory.
25 Frequency selector: This slide switch tunes the transmitter to one of three different carrier frequen-
cies within the transmitter's carrier frequency band.
26 Antenna: Permanently connected, flexible antenna.
27 Belt clip for fixing the transmitter to your belt.
28 Battery compartment lid with integrated screwdriver (28a).
28b Viewing window: The viewing window lets you check if there is a dry or rechargeable battery inside
the battery compartment. You can also place a white lettering strip (supplied) or a color code strip
(optional) behind the viewing window.
29 GAIN: This rotary control inside the battery compartment allows you to match the bodypack trans-
mitter input gain to the microphone or instrument you connected to the transmitter.
30 Carrier frequency label: The label on the transmitter rear panel indicates the name of the carrier fre-
quency band and the three carrier frequencies of your transmitter. Refer to the Manual Supplement
sheet for a color code table.
WMS 40 FLEXX
16:35 Uhr
Seite 17
2 Description
2.5 HT 40 FLEXX Handheld
Transmitter

2.5.1 Controls

Refer to fig. 3 on page 2.
Note:
2.6 PT 40 FLEXX Bodypack
Transmitter
2.6.1 Controls
Refer to fig. 4 on page 2.
Note:
17

Publicidad

Tabla de contenido
loading

Productos relacionados para AKG Acoustics WMS 40 PRO FLEXX

Tabla de contenido