Kickback And Related Warnings - Dremel 3000 Traducción De Las Instrucciones Originales

f. damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
g. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
h. use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
SErVicE
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
SaFETY inSTrucTiOnS FOr
all OPEraTiOnS
SaFETY WarninGS THaT arE cOMMOn
FOr GrinDinG, SanDinG, WirE BruSHinG,
POliSHinG Or aBraSiVE cuTTinG OFF
OPEraTiOnS
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher or cut-off tool. read
all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric shock,
fire and/or serious injury.
b. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
c. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can fly
apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
e. The arbour size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle of
the power tool. Accessories with arbour holes that do not
match the mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of control.
f. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. if power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. after inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no load speed for one minute. Damaged
accessories will normally break apart during this test time.
g. Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. as appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
h. Keep bystanders a safe distance away from work area.
anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond
immediate area of operation.
i. Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the operator.
j. use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable and
may lead to loss of control.
k. Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand
or arm may be pulled into the spinning accessory.
l. never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
m. Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
n. regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
o. Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p. Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
q. Do not work materials containing asbestos (asbestos is
considered carcinogenic).
r. Take protective measures when during work dust can
develop that is harmful to one's health, combustible
or explosive (some dusts are considered carcinogenic);
wear a dust mask and work with dust/ chip extraction when
connectable.

KicKBacK anD rElaTED WarninGS

Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory's rotation at the point of the
binding. For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may either jump toward
18