SpotOn 35010 Instrucciones página 5

INSTRUCTIONS IN ENGLISH | INVERSION TESTER
Understanding Inversion Intensity
The inversion intensity is the actual temperature difference between the upper temperature
reading the and lower temperature reading. It will display as a positive value when an
inversion is present and as a negative value when there is no inversion. Under normal
atmospheric conditions (no inversion) the intensity should show as a negative value of
0.5°F(0.3°C) or less. If an inversion is present then the intensity value will be a positive
value between 0.1°F(0.1°C) and 5.0°F(2.8°C). Any inversion should be considered significant
for applicators, with higher intensity values indicating a stronger inversion is present.
Changing the Battery
The LCD will show "REPLACE BATTERY!" when it is time to change the battery. There is no need
to replace a battery with a reading of 25% or higher. Remove the screw cover (6) of Fig. 1 by
rotating counter clockwise. A screwdriver may be required to loosen the cover. Gently pry out
the old battery with a small knife or tiny screwdriver as shown in (8) of Fig. 8, being careful not
to damage the battery holder. Replace with a new CR2032 lithium coin cell battery and replace
the screw cover. Tighten the cover clockwise until the o-ring seal is slightly compressed.
8
Fig. 8
CARE OF PRODUCT:
Store the meter inside the included carry case with dust cover in place to keep dust from covering
the temperature sensor or radiation shield. Dirt on the radiation shields can cause them to absorb
more sunlight energy and therefore cause errors in the air temperature readings. Use a damp
cloth to clean the radiation shields or meter body. Do not submerge meter in water because
this could damage the electronics. An occasional spray of water will not damage the unit.
TROUBLESHOOTING:
If the Red Sliding Pole Lock (2) of Fig. 1 won't stay in place while waving, try the following: With
the sliding pole lock in the folded position take a pair of pliers and gently squeeze the end of
the red tube opposite of the spring. This will cause the brass tube inside to become slightly
out-of-round which will allow it to grip on the spring when moved to the locked position.
5 Inversion Tester Item #35010
INSTRUCTIONS IN ENGLISH | INVERSION TESTER
WARRANTY, SERVICE, AND RETURNS:
One-Year Warranty
Innoquest, Inc. ("Innoquest") warrants this product to be free from defects in materials
and workmanship under normal use for a period of one (1) year from date of purchase. This
warranty extends only to the original purchaser and shall not apply to any product which,
in Innoquest's sole opinion, has been subject to misuse, alteration, abuse, or abnormal
conditions of operation or handling. Innoquest's obligation under this warranty is limited
to repair or replacement of the product which is returned to Innoquest.
accepts no liability for whatever damages may be caused by a malfunctioning product.
Repair & Service Policy
Products returned to Innoquest for repair or service must follow these guidelines: Return of the
product for warranty repair or service is the responsibility of the purchaser. Return of the product
for non-warranty repair or service, also the purchaser's responsibility, will carry a charge of $35 for
assessing the product's repair needs. Further work will not be completed without the purchaser's
approval.
Return Procedure
All returns, regardless of reason, must have a Return Merchandise Authorization ("RMA") number.
The purchaser must call Innoquest at (815) 337-8555 to obtain the RMA number prior to sending
any merchandise back. The RMA number must be displayed on the outside of the shipping
carton. All shipping charges will be paid by the purchaser. Innoquest is not responsible for
any package that is returned without a valid RMA number or for the loss of the package by any
shipping company.
Return for Refund Policy
We only accept returns of products purchased directly from Innoquest. Please return all other
products to the original place of purchase. A restocking fee (the greater of 15% of the purchase
price or $35) will apply to any returns sent back to Innoquest for a refund. For a refund, the
product must be in the original sealed packaging provided by Innoquest. If the unit was opened
but is completely functional and returned in good condition as determined by Innoquest, a
repackaging fee not to exceed $25 will be added to the restocking fee. No refund will be given for
damaged products.
Inversion Tester Item #35010
Innoquest
6