Brill Brillencio 41 B Manual Del Usuario página 24

For safety reasons, the petrol tank
and tank cap must be replaced if
damaged.
GB
Always replace damaged exhaust
components.
Check the cutting tools regularly
for damage and have them
repaired correctly if necessary.
Only have cutting tools replaced
by Brill Service or your authorised
specialist dealer.
Use /
A
Responsibility
Make sure that there are no
other people (especially children)
or animals within or near the
working area.
Powered equipment can cause
serious injuries! You are responsible
for safety in the area where you
are working. Never start the equip-
ment whilst tilted – risk of injury!
Always use the equipment solely
for the purpose described in the
operating instructions.
Never permit the combustion
engine to run in enclosed spaces
where dangerous exhaust gases
can collect.
Only work in daylight or with ade-
quate artificial lighting.
Ensure that you are standing
safely and on firm ground, even
on a slope. Work across the slope,
never up and down. Do not work
Warranty
The manufacturer warrants its prod-
ucts for exclusively non-commercial
use for a period of 24 months from
the date of original purchase.
This warranty does not affect
statutory warranty claims. The war-
ranty covers all substantial faults of
the product, which are caused by
defects in material and workman-
ship. If a product exhibits such a
defect we will, at our option, repair
or replace it without cost for parts
and labour provided the following
requirements are fulfilled:
24
on excessively steep slopes.
Be careful if you change direction
on a slope, turn the machine
round or draw it towards you.
Be careful if you are going back-
wards, risk of stumbling!
Only push the equipment at
walking pace.
Turn the motor off if the equipment
has to be tilted when transporting it
over surfaces other than grass and
if you are transporting the equip-
ment backwards and forwards
to the work area. Never use the
machine with damaged protective
devices or without protective
devices.
Never change the basic settings of
the machine or rev the engine too
hard.
Disconnect all the cutting tools
and drives before you start the mo-
tor.
When starting or operating
the starter switch take care as
stipulated by the manufacturer's
instructions.
Ensure that your feet are far
enough away from the cutting tool.
When starting or switching on the
motor, the machine should not be
tilted unless the machine has to be
raised during the process. In this
case only tilt it as far as absolutely
necessary and only raise the side
away from you.
The product must have been
.
sold to the customer in a legally
correct way.
The original receipt with the
.
customer's address, date of
purchase, model and product
designation is presented as
proof of purchase. The product
must have been purchased
within the EC.
The product was handled proper-
.
ly and according to the recom-
mendations in the operating
instructions. It is essential that the
Do not start the motor when
you are standing in front of the
discharge duct.
Keep your fingers and feet away
from the cutting tool!
Never lift or carry a machine with
the motor running.
Each time you have to work on
the machine or leave it or top it up,
always switch off the motor.
If you strike an obstacle when wor-
king, please disable the machine.
Remove the spark plug. Remove
the obstacle, check the equipment
for any damage and have it repai-
red if necessary.
If the equipment begins to vibrate
strongly, remove the spark plug
and ascertain the cause.
A
Taking a Break
Never leave the equipment
unattended. If you stop work,
switch the machine off and
remove the spark plug.
If you stop work to go to a different
work area, it is essential to turn the
equipment off and remove the
spark plug.
Beware of Environmental
A
Influences
Never use the equipment in the rain
or in damp, wet conditions.
Comply with local quiet periods in
your community!
product has been maintained and
cleaned according to the informa-
tion in the operating instructions.
No attempt to disassemble or
repair the product has been made
by either the buyer or an unautho-
rised third party.
It must be ensured that only
.
original replacement parts and
original accessories approved
by the manufacturer are used.
There may be an increased risk
of consequential damage and
accidents if non-original parts