Parameter List - SJE Rhombus VARIOspeed LCD Manual De Inicio Rápido

Parameter List

PARAMETERS
Basic Setup
P. 2 Minimum Frequency
P. 9 Motor Amps
P. 19 Motor Voltage
P. 44 Acceleration Time
P. 45 Decceleration Time
P. 133 Set Point Pressure
P. 575 Sleep Time
P. 576 Sleep Frequency
P. 577 Start Press. Differential
Advanced Setup
P. 4 HAND Frequency
P. 7 1st Acceleration Time
P. 8 1st Deceleration Time
P. 147 Thrust Bearing Switch Frequency (Well Pump)
P. 125 Maximum Frequency
P. 131 High Pressure Alarm
P. 1370 High Pressure Delay Time
P. 129 PID Proportional Band
P. 130 PID Integral Time
P. 935 Press. Sensor Max. Range
Advanced Pumping Functions
P. 127 Pre-charge Frequency
P. 761 Pre-charge ending level
P. 762 Pre-charge ending time
P. 1361 Detection Time for PID Output Hold
P. 1362 PID Output Hold Range
P. 1366 Sleep Boost Level
P. 1367 Sleep Boost Wating Time
P. 1368 Output Interruption Cancel Time
Caution! Always set Pre-charge Pressure (P.761) below the pressure set point (P.133). It is recommended for the Pre-charge pressure to be set at
least 20PSI below the pressure set point, even when only using Pre-charge timer.
*A setting of 9999 indicates the function is disabled.
1. Basic setup:
Minimum Frequency (P. 2)
The Minimum Frequency should be set to the minimum output frequency that the pump should be allowed to run.
Contact your pump manufacturer to obtain the pump safe operation ranges. Default value: 30.00Hz
Motor Amps (P. 9)
The VFD's electronic overload will signal an overload fault and protect the motor from damage in the event of an over-
load condition. Set the Motor Amps setting to the motor nameplate Full Load Amps for non-submersible pumps and to
the Motor Max Amps for submersible pumps. Default value: (motor nameplate)
Motor Voltage (P. 19)
Set the Motor Voltage setting to the voltage rating found on the motor nameplate. This value must not exceed the volt-
age of the incoming power. Default value: (same as incoming power)
Acceleration Time (P. 44)
Set the Acceleration Time to the rate at which the output frequency will accelerate while the VFD is operating above the
Thrust Bearing Switch Frequency. This time is based on the time the VFD would take to accelerate between 0 Hz to 60
Hz. Default value: 5 sec
VARIOspeed ® LCD Quick Start Manual
DESCRIPTION RANGE DEFAULT
0-120.00Hz 30.00Hz
0-500.0A XXX.XA
0-1000.0V
0-3600.0s
0-3600.0s
0-200.00PSI 55.00PSI
0-3600.0s
0-590.00Hz 35.00Hz
900.0-1100.0% 1005.00%
0-590.00Hz 50.00Hz
0-3600.0s
0-3600.0s
0-590.00Hz 30.00Hz
0-120.00Hz 60.00Hz
0-100.0% 95.0PSI
0-900.0s
0.1-1000.0% 100.0%
0-3600.0s
0-500.00PSI 200.00PSI
0-590.00Hz
0-100.0PSI
0-3600.0s
0-900.0s
0-50.0%
0-100.0%
0-360.0s
0-360.0s
9999
5.0s
5.0s
10.0s
2.0s
2.0s
2.0s
1.0s
9999
9999
9999
5.0s
9999
9999
0.0s
0.0s
5