Minimum Installation Dimensions; Measuring The Chassis Height; Determining The Installation Type; Special Accessory Installation - Truma Mover SR Instrucciones De Uso Instrucciones De Montaje

Minimum installation dimensions

The equipment can only be fitted to caravans / trailers within
the following dimensions.
Caravan floor
opt. 185
min. 30
max. 48
min. 60
max. 2400
all dimensions in mm
* with fully loaded vehicle
A distinction is made between L-profiled and U-profiled
chassis as shown in the illustration.
Caravan floor
L-profi i le

Measuring the chassis height

Frame height (Y) measured at distance of 106 mm (X) from
the outer edge of the tyre at height of hub / middle of tyre.

Determining the installation type

1. Standard installation
Standard installation is used with a U-profile or L-profile chas-
sis and a frame height (Y) of approx. 185 mm. No special
accessories are required.
2. Installation with chassis with U-profile or L-profile
and frame height of between 140 and 185 mm
With a chassis with a frame height (Y) of 140 mm to 185 mm,
1, 2 or 3 spacer plate sets and the screw set are needed to
compensate for the height.
3. Installation with chassis with U-profiles or L-profiles
with frame height of less than 140 mm
With a chassis with a frame height (Y) of less than 140 mm a
low chassis kit must be fitted to compensate for the height.
In Germany, the low chassis kit installation must
be accepted by a vehicle expert.
4. The AL-KO Vario III / AV installation kit must be used
with the AL-KO Vario III / AV chassis with a frame thickness of
less than 2.8 mm.
5. Installation with Eriba Touring chassis
The Eriba Touring mounting set is needed for the Eriba Touring
chassis.
•
max. 1860
U-profile

Special accessory installation

1. Set of screws
for height compensation with
spacer plates, max. 45 mm
eight DIN 933 screws
M10 x 95 8.8, galvanized,
part no. 60010-70000.
2. Spacer plate kit
(two 15 mm spacer plates)
for height compensation
max. 45 mm (3 Plates) at each
side (e.g. installed behind axle)
part no. 60010-66000.
3. Low chassis kit
For height compensation for
caravan / trailer with frame height
of less than 140 mm,
part no. 60010-64900.
In Germany, this installation
kit must be accepted by a
vehicle expert.
4. AL-KO Vario III / AV
Installation kit
For caravans with
AL-KO Vario III / AV Chassis
(frame thickness less than
2,8 mm) mandatory,
part no. 60010-21500.
Spacer plate set for
single-axle caravans up to
a total weight of 1700 kg
with chassis AL-KO Vario III / AV
(2 x 4 spacer plates à 15 mm)
to compensate height differences
of up to 60 mm
part no. 60010-70500.
5. Mover® mounting set
for Eriba-Touring
part no. 60030-09000.
Installation is not possible in
some cases because of
attachments to the underbody.
Contact your dealer if necessary.
Detailed installation instructions are provided with the
relevant mounting set.
The Mover® SR is not approved for installation on
caravans / trailers with any other chassis!
Any drilling (exception: when using low chassis kit*) or weld-
ing to the chassis is not allowed. Under no circumstances
remove any suspension components from the chassis.
* In the case of the AL-KO Vario III / AV Chassis, never drill
into the vehicle frame even if the flat frame kit is used.

Choice of location

The Mover® should preferably be installed in front of the axle,
but can also be installed behind the axle under special circum-
stances (e.g. lack of space). Only the bolts that are provided
must be used to secure the Mover® (or the add-on parts pro-
vided as special accessories).
17