Arregui PLUS C Manual De Instrucciones página 9

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 1
<EN>
BEWARE! Read these instructions
before installing and using the safe.
• To open the safe for the first time, see Point: 1. "Initial
Opening".
• For subsequent safe openings, type in one of the opening
codes available in the box and then turn the k. To learn
how to open and close the box see Point: 2. "Opening and
closing the safe".
• For security reasons, it is necessary to change the initial
codes from the factory setting user and super-user codes
and key in the numbers you choose. The new codes may
have between 3 and 8 digits. To learn how to change the
codes, see Point 3. "Changing opening codes".
• To activate the delay function, see Point: 4. "Opening the
delay switch function".
• For other setting adjustments, see Point: 5. "Screen and
sound setting configuration adjustments"
• In the event of any anomaly, such as batteries discharging,
for example, the safe has an external power outlet available
by means of a micro USB connector; see Point: 6." Use of
the external feed". In any case, to avoid drainage of the
batteries, please see Point: 7. "Battery level indicator". In
the event that the batteries become drained and you wish to
replace them, see Point 8. "Replacement of the batteries"
• Identification of the safe is done through the serial number
to be found on the front of the door and on the cover of
these instructions, which you will need in order to request
emergency openings, or spare parts, etc...
1. INITIAL OPENING
For initial opening of the safe, proceed as follows:
Install batteries (4xAA) in the external feed to be found in the
case, or either use an external lithium battery with a micro USB
connector.
• Insert the micro USB into the external feed connector.
• Insert the key (you will find inside the envelope) in the
keyhole.
• Type the factory setting user code
the
. Enter key.
• Turn the key with a half-turn to the right (in a clockwise
direction).
• Once open, pull out the external feed.
For proper functioning the safe requires 4 x alkaline batteries
1,5V (AA), which are placed in the battery holder situated at
the rear part of the door. To put them in place, open the lid
on the battery carrier and insert batteries as per the diagram
which you'll find inside. Once completed, the electronic
system will be activated.
To close the box, simply turn the knob to the left (in an anti-
clockwise direction)
2. OPENING AND CLOSING OF THE SAFE
• Put the key in the lock
• Press the
• Type in your user or super user opening code. The screen
• Press the
• To close the box, simply turn the knob to the left (in an
3. CHANGING THE OPENING CODES
1234 and then hit
The box has two opening codes available, a user code and
super-user code. Initially the codes are 1234 for the user code,
and 123456 for the super-user code.
To change the user code, proceed in the following manner:
• Open the box and don't close it until the procedure is
key, the keyboard will show "--------"
will continue showing the digits as you type them. If you
make a mistake and type in a mistaken code, you can type
in the code again just by typing the
enter key. If the code typed is correct a long
beep will sound and the screen will display "OPEN" for 5
seconds. Turn the knob to the right (clockwise) to open
the safe. If the code typed is incorrect, 4 short beeps
will sound and the screen will display "ERROR 1". In this
event, start the process again. "ERROR 2" will show if the
screen starts to wander again. The box allows a maximum
of 5 mis-entered attempts before displaying "ERROR 5",
before blocking new attempts for 5 minutes as a security
measure. During this period, the keypad will be locked and
the screen will display the "LOCKED 5" message, indicating
that a 5-minute blockage is in place. If any key is touched
during the 5-minute blocking period, the Word LOCKED will
appear on screen followed by a number which indicates
the number of minutes of blockage remaining ("LOCKED
4", "LOCKED 3" ...). Once the last minute has been entered,
there will be a 60-second countdown.
anti-clockwise direction).
complete
key again.

Publicidad

Tabla de contenido
loading

Tabla de contenido