Broan HI160I Instrucciones Para Instalación Y Uso página 2

ENGLISH
DESCRIPTION
This appliance is equipped with a completely automatic system (Advanced Sensor Control) capable to
manage all the functions of your hood. Thanks to the ASC, the air in the kitchen is costantly clean and odour
free without any manual intervention. The advanced sensor catches all sort of vapours, smokes and odours
caused by the cooking process. The ASC also captures an abnormal presence of GAS.
Moreover, this hood was born of the Home Comfort project aimed at maximum noise reduction. It also has
an Air Refresh function, which in perfect silence exchanges the air in the room by activating the hood every
50 minutes.
The unit can be found in filtering hoods or ducting hoods. In the Filtering version the air and the kitchen fumes that
are conveyed by the apparatus are depurated by the charcoal filter and put back into the room through the small grilles
of the ventilation flue (Fig. 1). ATTENTION: When using the filtering version, a charcoal filter and an air baffle (Fig. 1A)
must be used, which placed at the top of the structure, allows the air to recycle back into the room. In the Ducting version,
cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2).
INSTALLATION
ATTENTION: 3 persons are required for proper installation; the unit should be installed by a qualified operator.
Also follow carefully each step of the assembly instructions, and once installation has been completed, make sure
that the hood is firmly secured in place.
Before proceeding with assembly operations and to ensure easier manoeuvrability of the appliance, disengage
the grease filter: push the handle outwards and pull the filter downwards. 3).
Also remove the metallic surround by removing the 4 retaining screws (Fig. 4).
Separate the upper part of the telescopic structure from the lower part by removing the 4 retaining screws and
the 4 washers (Fig. 5).
Essential requirements for assembly: – Prepare electricity supply inside the the telescopic flue – If your appliance
is to be installed as a Ducting version, prepare the air evacuation hole.
When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short
as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which
vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section
(diameter: 150 mm).
ASSEMBLY
Ducting version:
Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe
all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must
correspond with the axis of the extractor hood controls.
Secure the upper part of the telescopic structure to the ceiling using the 4 screws and pads supplied (Fig. 6); pay close
attention since the positioning of the structure determines the final position of the extractor hood. During this operation,
pass the air air evacuation pipe inside the telescopic structure and the electricity supply through the specific hole
in the structure (Fig. 6).
Fit the adapter flange on the air output mouth of the motor. 7).
Secure the motor unit to the lower telescopic structure, using 4 nuts and 4 washers (Fig. 8). This block should then
be secured to the upper telescopic structure (Fig. 9) previously secured to the ceiling (with the 4 screws and 4 washers
removed previously). Adjust the height of the telescopic structure using the four screws (Fig. 9) bearing in mind that
the extractor hood must be at minimum distance of 650 mm from the cooking top. (Fig.10).
Through the apertures in the telescopic structure, secure the air evacuation pipe to the adapter flange using a band
(Fig.11); the pipe and band are not supplied.
Make the electrical connection using the power supply cable.
Take the upper flue (the one with slots) and insert it into the telescopic structure, with the slots at the bottom; secure
it to the structure with 2 screws (Fig. 12).
Take the lower flue and insert it in the same way into the other flue; move it upwards and secure it with 4 screws (Fig.13).
Insert the control box in its seat and secure it by tightening the 2 screws inside the lower flue (Fig.14).
Refit the metallic surround removed prior to the installation procedure (Fig. 4). Pay special attention to the direction,
since the slots ("A". - Fig. 4) must align with the sensor mounted in the inside left part of the extractor hood.
Connect the halogen spot lights (Fig. 15).
Refit the grease filter.
Filtering Version:
Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe
all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must
correspond with the axis of the extractor hood controls.