Numark CD MIX Guia Del Usuario página 4

14. PITCH FADER – The pitch can be changed by pressing the PITCH button, lighting the PITCH LED,
and then move the fader. The pitch will not be changed if the PITCH LED is off.
15. PITCH BEND -/+ – You can use these two pitch bend buttons to temporarily adjust the pitch and tempo
of the music.
16. KEYLOCK – Engages the Keylock feature, which locks the musical key of the track to the original key
(as if it were playing with 0% pitch adjustment). You can then adjust the tempo of the track without
affecting its key or pitch.
17. TAP – Tap this button in time with the beats of the music on that deck. This will enter a new BPM
("beats per minute") reading for that track, which will be shown on the LCD. You can allow the
automatic beat-counter to read the track's BPMs by holding it down until "AUTOBPM" is shown on the
LCD.
18. RELAY – Press this button to activate or deactivate Relay Play. When activated, relay play will cause
the opposite deck to start playing whenever the currently playing deck stops. Playback will alternate
between the two decks until one of the decks reaches the end of its disc or until Relay Play is
deactivated.
19. TIME – Switches the time display between "ELAPSED" playing time, "REMAINING" time on the track,
and "TOTAL" remaining time on the entire CD.
20. SNGL – Press this button to toggle between Single Play (the deck will stop at the end of each track) or
Continuous Play (the entire disc will be played without interruption).
21. ID3 TAG – Press this button to display additional MP3 information. Press it more than once to toggle
through all the available information, including the track title, artist name, name of the current folder,
and file name.
22. LCD – Indicates all the functions, as they are occurring, with the CD.
23. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks
are located on the rear panel.
24. CHANNEL GAIN – Adjusts the channel's pre-fader and pre-EQ gain level.
25. CHANNEL TREBLE – Adjusts the high (treble) frequencies of the corresponding channel.
26. CHANNEL MID – Adjusts the mid-range frequencies of the corresponding channel.
27. CHANNEL BASS – Adjusts the low (bass) frequencies of the corresponding channel.
28. CHANNEL FADER – Adjusts the audio level on the corresponding channel.
29. CHANNEL CUE – Sends pre-fader audio to the Cue Channel for headphone monitoring.
30. CUE MIX – Turn to mix between Cue and Program in the Headphone channel. When all the way to the
left, only channels routed to CUE will be heard. When all the way right, only the Program mix will be
heard.
31. CUE GAIN – Adjusts the audio level of the Cue channel.
32. HEADPHONES – Connect your 1/4" or 1/8" headphones
to this output for cueing and mix monitoring.
33. MIC ON / OFF – Mutes and unmutes the microphone signal. When muted, the microphone signal will
not be routed to the Master mix.
34. CROSSFADER – Blends audio playing between Channels 1 and 2. Slide this to the left to play Channel
1 and slide to the right to play Channel 2.
Note: The crossfader is user replaceable. Simply unscrew the two large screws which hold it in place,
lift it out and disconnect the cable. Re-attach the new crossfader and screw the mounting plate back
onto the unit. Test and confirm new crossfader is working as intended.
35. FADER START – When fader start is "ON," move the CROSSFADER to a side to cause that deck to
start playing automatically (if it is paused). When fader start is "OFF," you will need to manually start
playback on each deck.
36. STEREO LEVEL INDICATOR – Displays the audio level of the Program mix.
37. MASTER VOLUME – Adjusts the output volume of the Program mix.
38. ZONE VOLUME – Controls the audio level of the Zone output.
39. MONO / STEREO – Adjusts the Program mix for stereo or mono operation.
40. DEVICE HOLDER – Rest your MP3 player or iOS device here.
41. BLUETOOTH CONTROLS – Controls the functions for your Bluetooth device's menus while it is paired
to the mixer. These controls include Pair, Track Skip Backward, Track Skip Forward, and Play/Pause.
Press and hold the Pair button for 2 seconds to put CDMix Bluetooth into Pairing Mode. Hold down the
Pair button for 2 seconds to disconnect Bluetooth pairing. The Bluetooth logo in the center of the
Bluetooth Controls will no longer illuminate to show your Bluetooth device has been unpaired. See the
BLUETOOTH PAIRING section for more information.
Note: When connecting microphones,
make sure the mic channel's gain knob is
at the lowest setting before connecting it.
4