Operating The Nailer - Campbell Hausfeld CHN101 Manual Del Usuario

General Safety Information
(Continued)
•
Always remain in a fi rmly
balanced position when
using or handling the
nailer.
•
Do not remove,
tamper with, or
otherwise cause the
Work Contact Element
(WCE) or trigger to
become inoperable.
Do not operate any tool which has
been modifi ed in a like fashion.
Death or serious personal injury
could result.
•
Do not touch the
trigger unless driving
nails. Never attach air
line to nailer or carry
nailer while touching
the trigger. The tool could eject a
fastener which will result in death
or serious personal injury.
•
Always disconnect
the tool from the
power source
when unattended,
performing any
maintenance or repair, clearing a
jam, or moving the tool to a new
location. Always reconnect the air
line BEFORE loading any fasteners.
Do not load the tool with fasteners
when either the trigger is depressed
or the Work Contact Element (WCE)
is engaged. The nailer could eject
a fastener causing death or serious
personal injury.
•
Always fi t tool
with a fi tting or
hose coupling on
or near the tool in
such a manner that
all compressed air in the tool is
discharged at the time the fi tting or
hose coupling is disconnected. Do
not use a check valve or any other
fi tting which allows air to remain in
the nailer. Death or serious personal
injury could occur.
•
Never place hands or any
other body parts in the
nail discharge area of the
nailer. The nailer might
eject a fastener and could
result in death or serious personal
injury.
•
Never carry the
nailer by the air hose
or pull the hose to
move the nailer or
a compressor. Keep
hoses away from heat, oil and sharp
edges. Replace any hose that is
damaged, weak or worn. Personal
injury or tool damage could occur.
•
Always assume the nailer contains
nails. Respect the tool as a working
implement; no horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Do not point
the tool toward yourself or anyone
whether it contains fasteners or not.
Accidental triggering of the nailer
could result in death or serious
personal injury.
•
Do not drive a nail
on top of other nails.
The nail could glance
and cause death or
a serious puncture
wound.
•
Do not operate or
!
allow anyone else
to operate the nailer
if any warnings or
warning labels are
not legible. Warnings or warning
labels are located on the nailer
magazine and body.
•
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make
the tool unusable or unsafe. If the
tool has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
•
Do not make any modifi cations to
the tool without fi rst obtaining
written approval from Campbell
Hausfeld. Do not use the nailer if
any shields or guards are removed
or altered. Do not use the nailer as
a hammer. Personal injury or tool
damage may occur.
•
Avoid long extended periods of
work with the nailer. Stop using the
nailer if you feel pain in hands or
arms.
•
Always check that the Work
Contact Element (WCE) is operating
properly. A nail could accidentally
be driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
•
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
•
Avoid using the nailer when the
magazine is empty. Accelerated wear
on the nailer may occur.
3
•
Clean and check all air supply hoses
and fi ttings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fi ttings.
Tool performance or durability may
be reduced.

Operating The Nailer

LUBRICATION
This nailer requires lubrication before
using the nailer for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
WARNING
damaged by excessive lubrication.
Proper lubrication is the owner's
responsibility. Failure to lubricate the
nailer properly will dramatically shorten
the life of the nailer and void your
warranty.
1. Disconnect the air
supply from the nailer
to add lubricant.
2. Turn the nailer so the air
inlet is facing up. Place
4-5 drops of 30 W non-
detergent oil into air inlet.
Do not use detergent
oils, oil additives, or air tool oils.
Air tool oils contain solvents which
will damage the nailer's internal
components.
3. After adding oil, run
nailer briefly. Wipe
off any excess oil
from the cap exhaust.
CHN101
The work surface
can become
OIL OIL
www.chpower.com