Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
V
Volts
A
Amperes
Hz
Hertz
W
Watts
min
minutes
Alternating
Current
Date Code Position (Fig. B)
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
Year of Manufacture Package Contents
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Cable cross-sectional
area (mm
)
2
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes Cable rated current (Ampere)
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Direct Current
n
No-Load Speed
0
Class II Construction
Earthing Terminal
Safety Alert Symbol
Revolutions or
/min.
Reciprocation per
minute
2018 XX XX
Cable rated current
(Ampere)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
THE PACKAGE CONTAINS
1 1/4 Sander
1 Punch Plate
1 Dust Bag
1 Instruction manual
1 Warranty card
1 Service center list
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
Description (Figura 1)
WARNING: Never modify the power tool or any
part of it. Damage or personal injury could result.
1. On/off switch
2. Dust Bag
3. Sanding Base
4. Paper clamp lever
5. Punch Plate
6. Dust Bag Collar
7. Dust extraction Outlet
ASSEMBLY AND ADJUSTMENT
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or
removing/installing attachments or accessories. Before
reconnecting the tool, depress and release the trigger
switch to ensure that the tool is off. An accidental start-up
can cause injury.
Dust Extraction (Figura 2)
60
WARNING: Since woodworking with a sander produces
dust, always install a dust bag designed in compliance with
the applicable directives regarding dust emission.
10
WARNING: Do not use a dust bag or vacuum extractor
without proper spark protection when sanding metal.
15
Your sander has a dust extraction methods: a built-in outlet
20
(g) which allows either the supplied dust bag (b) or a shop
vacuum system to be connected.
25
TO ATTACH THE DUST BAG
-
♦ While holding the sander, fit the dust bag collar (f) to
-
the outlet (g) as shown in Figure 3.
♦ Turn the collar (f) anticlockwise to lock the dust bag
6
(b) in place.
6
TO EMPTY THE DUST BAG
15
NOTE: Be sure to wear approved eye protection and
approved dust mask when performing this procedure.
15
For efficient dust extraction, empty the dust collector when
20
it is about one third full.
♦ While holding the sander, turn the collar (f) clockwise
-
to unlock the dust bag (b).
ENGLISH (
Original Instructions)
17
Publicidad
Tabla de contenido
