Usb Ports - Stanley FATMAX PP1DCS Manual De Instruccion

it may overheat. This could damage the compressor. If the compressor must be operated for longer periods: every 10 minutes
press the Compressor Power Button to turn the compressor off, then restart after a cooling down period of approximately 30
minutes.
Inflating Tires or Products With Valve Stems
1. Screw the SureFit nozzle onto the valve stem. Do not overtighten.
®
2. Press the Compressor Power Button. A beep will sound and the backlit LCD screen will display the following:
The Compressor Icon will light and the digital display will alternately show the flashing pre-set psi value (that was last set by
the compressor pressure control buttons) and the current pressure of the item being inflated (which will light solid).
3. Press the "+" and "–" Pressure Control Buttons to set the desired pressure from a range pre-set values (between 3 and 120),
which will display on the backlit LCD screen. The unit will sound a beep with each press of the buttons (holding the button
speeds up the upward or downward value selection). Once the desired pressure has been entered, release the button and
the flashing digital display will show the new selected pressure, as follows:
The new selected value is now stored in the unit's memory until it is manually reset.
4. Press the Compressor Power Button once more to begin inflating. The Compressor Icon will flash and the digital display will
only show the current pressure value (which will light solid) to indicate the compressor is activated. Monitor the pressure on
the LCD screen.
IMPORTANT NOTE: To interrupt during inflation, press the Compressor Power Button again.
5. When desired pre-set pressure is reached, the compressor will automatically stop.
6. Press the Compressor Power Button again to turn off the unit.
7. Unscrew and remove the SureFit
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and SureFit
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the SureFit
2. Insert the nozzle adapter into item to be inflated.
3. Follow steps 2 through 4 of the "Inflating Tires or Products With Valve Stems" section.
IMPORTANT: Small items such as volleyballs, footballs, etc. inflate very rapidly. Keep this in mind when setting pressure. Take
extra care not to over-inflate.
4. When the desired pressure is reached, the compressor will automatically stop. Press the Compressor Power Button again to
turn off the unit.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the SureFit
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, SureFit

USB PORTS

The USB Power Button and the four USB Ports are located on the left hand side of unit. The USB Power/Fault Indicator is a
translucent ring around each of the four USB Ports. Refer to the "Features" section to locate.
IMPORTANT NOTES:
The top two USB Ports provide a total of 3.1A (5V each). The bottom two USB Ports provide a total of 3.1A (5V each).
When the USB Ports are in use, the unit will monitor for the following USB fault conditions on all the USB Ports: thermal fault,
low battery voltage fault, overload and short circuit. The USB Power/Fault Indicators are divided into an upper set and a lower
set. The upper set detects fault conditions in the first two USB Ports; the lower set monitors in the last two USB Ports. If a
fault condition exists in either of the first two USB Ports, the upper set of USB Power/Fault Indicators will flash blue. If a fault
nozzle from the valve stem.
®
nozzle in storage compartment.
®
® nozzle. Do not overtighten.
®
nozzle and nozzle adapter in the storage compartment.
®
nozzle.
13