Leo; SavingYourSettings; Selecting The Presets - Monitor Audio Gold W15 Manual Del Usuario

Setting the EQ Using the Remote
With the Gold W15 powered up and out of standby mode, follow
the next steps to set the EQ:
1. Press the RIGHT arrow 3 times. The display will change
to LPF then PHA then EQ
2. Press ENTER. The display will change to show the
current setting, eg. OFF
3. Press the UP / DOWN arrows to adjust the setting
4. Press ENTER to select and save. The display will flash
twice to confirm selection and then display EQ
Setting the EQ Using the Control Panel
Encoder
With the Gold W15 powered up and out of standby mode, follow
the next steps to set the EQ:
1. Press the encoder down. The display will change to LPF
2. Rotate the encoder 2 positions to the right. PHA then
EQ will be displayed
3. Press the encoder again to enter the EQ menu. The
display will change to show the current setting, eg. OFF
4. Rotate the encoder left or right to change the setting
5. Press the encoder to select and save. The display will
flash twice to confirm selection, and then display EQ

LEO

After the room correction has been run (refer to page 8), it can
then be enabled/ disabled within the menu:
Setting the LEO Using the Remote
With the Gold W15 powered up and out of standby mode, follow
the next steps to set the LEO:
1. Press the RIGHT arrow 3 times. The display will change
to PHA then EQ then LEO
2. Press ENTER. The display will change to show the
current setting, eg. On
3. Press the UP / DOWN arrows to adjust the setting
4. Press ENTER to select and save. The display will flash
twice to confirm selection and then display LEO
Setting the LEO Using the Control Panel
Encoder
With the Gold W15 powered up and out of standby mode, follow
the next steps to set the LEO:
1. Press the encoder down. The display will change to PHA
10
2. Rotate the encoder 2 positions to the right. EQ then
LEO will be displayed
3. Press the encoder again to enter the LEO menu. The
display will change to show the current setting, eg. On
4. Rotate the encoder left or right to change the setting
5. Press the encoder to select and save. The display will
flash twice to confirm selection, and then display LEO

SavingyourSettings

Once you have been through the menu, the chosen settings can
then be saved to one of the 3 presets (per input). This can be
done by either the remote or the encoder:
SavingyourSettingsUsingtheRemote
With the Gold W15 powered up, out of standby mode, the
desired input selected, and the system set up using the guides
previously, follow the next steps to save the settings:
1. Press and hold P1 (or the appropriate preset number)
on the remote for 3 seconds. The display will change
to SEt
2. The display will then change to show the preset number,
eg. 1. Then back to the default display " . "
SavingyourSettingsUsingtheControl
Panel Encoder
With the Gold W15 powered up and out of standby mode, the
system set up using the guides previously, follow the next
steps to save the settings:
1. Press and hold the encoder down for 3 seconds. The
display will change to PRe
2. Rotate the encoder left or right to show the current
Preset location. eg. 1
3. Rotate the encoder left or right again to change the
Preset location, press and hold for 3 seconds to store.
The display will show SEt
4. The display will flash twice with the preset number to
confirm selection, and then back to the default display
" . "

Selecting the Presets

If a number of different presets have been stored for each
input, they can be recalled by following these steps:
Selecting a Preset Using the Remote
With the Gold W15 powered up and out of standby mode, the
system set up using the guides previously, follow the next
steps to recall a preset:
Gold W15 Owners Manual