Technical Data; Instructions For Use; Putting The Machine Into Service - Grillo G52 Manual De Uso Y Mantenimiento

Engine: 4 stroke petrol engine TECUMSEH GEOTECH 50 - LOMBARDINI LGA 226 - BRIGGS & STRATTON INTEK
5.5 HP – HONDA GC 160
Gearbox: 2 speed gears in oil bath (one forward and one reverse).
Power-take-off: at 644 rpm as walking tractor in anti-clockwise direction of rotation; at 965 rpm as motor mower in
clockwise direction of rotation.
Safety device: engaging the reverse gear the rotary tiller disconnects automatically.
Handlebar: adjustable in height and sideway and revolving.
Rotary tiller: standard: 500 mm (adjustable 500 - 370 mm).
Attachments: rotary tiller, cutter bar, snow thrower, rotary cutter, spraying pump, cage steel wheels, wheel-weights,
wheel extensions, barrow, grass cutter cm. 50, combined furrower, trailer, tilting front dozer blade cm. 80.
Weight: machine in working order with rotary tiller: 66 kg.
Speeds with 13.50-6 tires:
As walking tractor: forward speed 1.4 km/h - reverse speed 2.2 km/h.
As motor mower: forward speed 2.2 km/h - reverse speed 1.4 km/h.

PUTTING THE MACHINE INTO SERVICE

1) Fill engine oil to level (please refer to relevant engine handbook).
2) Check the BLASIA 220 gearbox oil (or international equivalent ISO-L-CKD, DIN 51502 PGLP) or ROTRA MP 80W90
(API GL 5).
Do not turn on the engine without first checking:
– all screws and nuts are well tightened;
– the reversing device lever on gearbox housing is on the right position;
MOTOCOLTIVATORE (walking tractor) A
MOTOFALCIATRICE (motor mower) B (fig. 1)
– the attachments engaging lever (fig. 2 no. 3) is in idle position (in the fig. no. 2 the attachment is engaged) the
advancement control lever (fig. 2 no. 1) are in idle position (fig. 3);
– air filter is clean (fig. 4 - fig. 6);
– to fill in the tank use a funnel with a very fine filter;
– the attachments are properly fixed to the machine (fig. 5-6);
– adjust handlebar height (fig. 2 no. 4).
HOW TO START THE ENGINE
Open the fuel tap (fig. 7 no. 2), push the gas control lever halfway (fig. 2 no. 5). Press the dead-man handle (fig. 2 no. 6).
If the engine is cold operate the starter device on the carburettor (fig. 7 no. 1) choke position (please refer to relevant engine
handbook); grip the starting handle (fig. 8) and jerk strongly. When the engine has started it is necessary to set the starting
device back to the «RUN» position; then the gas lever slowly to the minimum.
HOW TO START THE MACHINE
Keep the engine at a low rating; engage the implement by leaving the lever no. 3 (fig. 2); accelerate properly and leave
the wheel engaging lever (fig. 2 no. 1): the machine will start moving. Pulling the lever no. 1 (fig. 2) the machine stops.
Pulling the lever no. 2 (fig. 2) the machine goes backward. To lock the levers, hook the lever clip (fig. 3). Operating the
lever (fig. 9) it is possible to adjust the handlebar laterally «one right-hand position - one left-hand position» either as
walking tractor or as motor mower.
END OF WORK
When work is ended, to stop the engine; press the button (fig. 2 no. 8) and close the fuel tap (please refer to relevant engine handbook).
POSSIBLE INCONVENIENCES AND SOLUTIONS
The following inconveniences can be fixed up by the operator himself. If the engine does not start, check in the following order that:
– the fuel tank is at least half full;
– the fuel tap is open;
– the starting device is operating (when the engine is cold) fig. 7 CHOKE;
– fuel gets to the carburettor;
– the breather hole on the tank plug is not obstructed;
– the air filter is clean (fig. 4 - fig. 6);
– current gets to the spark plug (fig. 10); (please refer to relevant engine handbook). If current does not arrive, after
checking the electric cables have no defects and the plug is clean, change the plug taking care to buy another one with
the same heat rating. If this attempt also should turn out to be useless, the failure must be searched in the magneto
flywheel; at this point it is advisable to go to the nearest service-centre.

TECHNICAL DATA

INSTRUCTIONS FOR USE

7