Pet Mate CAT MATE Elite Instrucciones página 6

7. To View How Long Since the Cat(s) Last Used the Cat Flap
7.1 To view how many hours and minutes since cats 1, 2 or 3 last used the cat flap,
press the '+' button.
7.2 The display will show the symbol for 'CAT 1' and how many hours and minutes
ago 'CAT 1' used the flap up to a maximum of 99 hours.
7.3 Press '+' again for similar information on Cats 2 and 3.
7.4 Press '+' a fourth time (or leave for 20 seconds) and the normal display will be
resumed.
8. Access Options
The access options available are shown below.
'In & Out' Your cat(s) can come in and out of the flap
'In Only' Your cat(s) can come in through the flap but cannot leave through
the flap
'Out Only' Cat(s) can go out through the flap but cannot enter through the flap
'Locked' Cat(s) cannot use the flap
Select an access option as follows:
8.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.
8.2 Repeatedly press the '4 WAY' button to scroll through the available access
options, until you come to the one you want.
8.3 Press the 'PROG' button to save the setting.
8.4 Setting Timer Control/Clock for ALL Cats
If you wish to set your cat flap to ensure that ALL cats have a particular access option,
over a selected timed period, e.g. to keep your cat(s) in at night between 19:00 and
06:00, you will first need to decide:
a) Which lock setting should apply DURING the timed period, (in the above example
'IN ONLY' will apply). Outside the timed period, the lock setting made in 8.1 to 8.3
will apply.
b) When the timed period should 'START' (In the above example 19:00hrs).
c) When the timed period should 'FINISH' (in the above example 06:00hrs).
d) You will also need to know the current time.
Proceed as follows:
NOTE: if you do not press a button for more than 60 seconds the display will revert to
normal and you will need to start again.
8.4.1 Press the 'TIMER' button for 5 seconds until the Timer function indicator
flashes.
10
8.4.2 Repeatedly press the '4 WAY' button to select the required access options from:
'IN & OUT', 'IN ONLY', 'OUT ONLY', 'LOCKED' or 'OFF'.
8.4.3 Press the 'PROG' button to save the setting.
8.4.4 The display will show time with the Minute symbol flashing. Repeatedly press
the '+' button until the current Minutes setting is shown (i.e. 10 if the current time
is 12:10).
8.4.5 Press the 'PROG' button to save the setting.
8.4.6 The display will now show the time with the Hour symbol flashing.
If you wish to change between a 24 hour clock and AM/PM setting, press the
'TIMER' button.
8.4.7 Repeatedly press the '+' until the correct Hour setting is shown (e.g. 12 if the
current time is 12:10).
8.4.8 Press the 'PROG' button to save the setting.
8.4.9 The display will show the word 'START' and the minutes will flash. Press the
'+' button until the desired minutes setting is shown, (in the above example
'00'). Press the 'PROG' button to save the setting.
8.4.10 Then set the hours in the same way (in the above example 19:00).
8.4.11 The display will show the 'FINISH' time. Set in the same way as the 'START'
time. Remember to press 'PROG' to save the setting.
When the Timer is set, the Timer function indicator ( 5 , Fig. 1) will be shown on the
display.
When the timed lock is active, the access option symbol chosen at 8.2 will flash slowly.
To check the time settings, briefly press the 'TIMER' button and release. The display
will show the timed access option selected and the 'START' time. Press the 'TIMER'
button again to show 'FINISH' time. The display will revert to current time after 5
seconds.
To cancel timer control and revert back to the normal access option:
8.4.12 Press the 'TIMER' button for 5 seconds.
8.4.13 Press the '4 WAY' button and go back through the options until you come to
'OFF'.
8.4.14 Press the 'PROG' button 3 times to keep the current clock time and return to
the normal display.
9. Battery Replacement
When the low battery indicator ( 3 , Fig. 1) comes on, alkaline batteries should be
replaced. (See Section 2).
Please note, after fitting new batteries:
• Low battery indicator may remain on for up to 15 minutes.
• Flap will remember all microchip(s) and I.D. Disc(s), Lock Settings and Lock Times
but CURRENT TIME WILL NEED RESETTING. (See section 8.4).
11