CAME ZVL370.01 Manual De Instrucciones página 23

A - Memorising a channel (fig.1):
1. Press and hold down button "P3" MEMO: The LED "L2" will flash slowly.
2. At the same time activate the transmitter which is to be memorised.
3. Hold down button "P3" MEMO until LED "L2" starts to flash again.
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the channel is different or it is a different
transmitter the memorisation attempt will abort without success)
6. End of memorisation: The LED "L2" will remain lit for 2 seconds, indicating that the transmitter has
been correctly memorised.
Note: it is not possible to memorise a code which is already in memory: if you attempt this, the LED will switch
off when you activate the transmitter (point 2).
Only after releasing the button "P3" MEMO will you be able to continue the memorising procedure.
If after activating the transmitter for the first time you wait for more than 15 seconds without activating the transmitter
a second time the memorisation attempt will abort without success.
B - Cancelling a channel (fig.1):
1. Press and hold down the button "P4" DELETE: The LED "L2" will flash quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED "L2" will remain lit for 2 seconds, indicating that the transmitter has been cancelled.
Note: if the user that you wish to cancel is not in memory, The LED will stop flashing; Only after releasing the button
"P4" will you be able to continue the cancellation procedure.
For both the memorisation and cancellation procedures, if the button is released before activating the
transmitter the procedure will abort.
C - Cancelling all user codes from memory (fig.1):
1. Keep both buttons pressed down ("P3+P4") for more than four seconds
2. LED "L2" will remain lit during the entire cancellation time (about 8 seconds).
3. LED "L2" switches off when the cancellation procedure has terminated.
Note: when the memory is almost full the time required to search for a user code could take up to 1 second
from when the command was received.
If LED "L2" remains alight memory is completely full. To memorise a new transmitter you will first have to
cancel a code from memory.
D- Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the receiver container) if jumper "J2"
has been inserted (fig.1).
1) Makesurethatthejumper"J2"hasbeeninserted(fig.1).
2) Using a transmitter, in which at least one channel button "A,B,C or D" has
already been memorised in the receiver, press the button in the transmitter
as shown in figure.
Note:allthereceiverswithinrangewhenthechannelbuttonispressed(and
which have at least one of the transmitter channel buttons memorised) will
activate their signal buzzer "B1" (fig. 1).
3) Press one of the channel buttons on the same transmitter. The receivers which do not contain that channel code
will sound a five-second long "beep" and will then disactivate. The receivers which contain the channel code will
sound a one-second long "beep" and will enter the programming via radio mode.
4) Press the previously chosen channel buttons on the transmitter which you wish to memorise; the receiver will sound
2 "beeps" of half a second each after which the receiver will be ready to receive another code.
5) To leave the programming mode wait for 5 seconds without pressing any buttons. The receiver will sound a
five-second long "beep" and will then exit the programming mode.
• When the memory is entirely occupied the buzzer will sound 10 rapid "beeps" and will automatically leave the
"programming via radio" mode. LED "L2" will remain lit. The same signal is given each time you try to enter
"programming via radio" when the memory is full.
All rights reserved. Unauthorised copying or use of the information contained in this document is punis
Drawing number :
Product Code : RCQ449100
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/40183
23
Description : MEMORIZZAZIONE CODICE TX-RX
DM0531
Date :
13-04-2001