Residual Risks; Assembly And Adjustment; Preparation Before Use - Stanley STGS7115 Manual De Instrucciones

applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
e. Always use undamaged wheel flanges that are
of correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
f. Do not use worn down wheels from larger power
tools. Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and may
burst.

RESIDUAL RISKS

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
f Impairment of hearing.
f Risk of personal injury due flying particles.
f Risk of burns due to accessories becoming hot during
operation.
f Risk of personal injury due to prolonged use.
f Risk of dust from hazardous substances.
FEATURES (Fig. A)
Warning! Never modify the power tool or any part of
the tool, otherwise it may cause damage to the tool or
result in personal injury.
1. On/off switch
2. Spindle lock
3. Guard

ASSEMBLY AND ADJUSTMENT

Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
Attaching and removing the wheel guard (Fig. B)
Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing up.
2. Bring the flange of the guard (3) collar over the groove
(9) of the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (11) are tightened.
Removing the guard
1. Loosen the screws (11) on the guard collar
(Do not remove the screws).
2. Pull up the guard (3).
Warning! Do not operate the tool when the safety guard
is not in place.
Note: Refer to the grinding accessories chart at the end
of this section for accessories that can be used together
with this angle grinder.
Attaching and removing grinding wheels
(Fig. C and D)
Warning! Do not use damaged grinding wheels.
1. Place the tool on a work bench, groove facing up.
2. Attach the inner flange (4) correctly on the output
shaft (5) (Fig. C).
3. Place the grinding wheel (6) on the inner flange (4).
When attaching a grinding wheel with a raised center,
make sure that the raised center (7) faces the inner
flange (4).
4. Tighten the outer flange (8) until the output shaft (5)
(Fig. D). When attaching the grinding wheel, the ring
on top of the outer flange (8) must face the wheel.
5. Press the spindle lock (2) and prevent the spindle (5)
from rotating until it locks in place.
6. Use the pin spanner to tighten the outer flange (8).

PREPARATION BEFORE USE

f Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding
wheels that are overly worn.
f Make sure that the inner and outer flanges are
attached correctly.
f Make sure that the abrasive or grinding wheels
are rotating in the direction of the arrows on the
accessories and tool.
OPERATION (Fig. E)
Instructions
Warning! Always observe the safety instructions and
applicable regulations.
Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
Warning!
f Make sure all materials to be grinded are secured in
position.
ENGLISH • 21