Publicidad
Idiomas disponibles
Idiomas disponibles
30. Identify the fixing point of element F01 on the floor in correspondence with the first baluster C03 (H. 1190 mm -
46
/
"). After checking that it is vertical, take off the column and drill with a D. 8 mm - 5/ 1 6" bit. Use the elements
7
8
B11, B12 and C31 (Fig. 1). If installing outdoors seal the point where element F01 rests on the ground with
acetic silicone (not included).
31. Position the first baluster C03 (H. 1190 mm - 46
Finally secure element F07 to baluster C03 by means of the components C31.
32. Heat the handrail A02 until it is malleable (fig. 10):
1) rest the handrail on the cover of the wooden box,
2) slowly heat it performing circular movements without stopping,
3) overturn the handrail and repeat the operation.
33. Position the handrail A02 on the balusters C03 (H. 1190 mm - 46
C03 (H. 1190 mm - 46
lower part before it cools (fig. 9).
34. Cut the exceeding part of handrail A02 so that it does not hamper the operations.
35. Drill handrail A02 in correspondence with the holes present on all the elements B53 and fix it with elements
B54 and B55 (fig. 1).
36. Insert the remaining balusters C03 in the treads L02 in close succession (for a D. 120 cm - 47
only one intermediate column H.1095 mm - 43
intermediate columns H. 1060 mm - 41
they are vertical and fix them to the handrail A02 using elements B54 and B55.
37. In correspondence with the first baluster C03 of the staircase, perform a final cut of the handrail A02.
38. Insert element A03 on handrail A02 (eliminate burrs due to cut) using the glue X01 after heating the end of
handrail A02 (fig. 1).
39. Secure elements C31, D32 and D33 in a permanent manner using the part C36.
40. Complete the railing assembly by inserting elements B82 into the lower part of the balusters C03 (fig.1).
Assembling the balustrade
41. Screw column C04 onto element G01 protruding from the landing E03 (fig. 1).
42. Fasten element B01 onto column C04 using element C31 and seal it with silicone if installing outdoors (Fig. 1).
43. Fix elements F01 using the components B89, B27, B23 in the holes present on the landing E03 as in fig. 1.
44. Position the shorter balusters C03 H.935 mm - 36
seal the space between the two elements if installing outdoors) and tighten element C31 (fig. 1). In the hole
with the elements D32 and D33 on the landing E03 use a baluster C03 H.1060 mm - 41
95 mm - 3
/
".
3
4
45. Secure the handrail A18 using elements B54 and B55 (fig. 1).
46. Connect the end part of the railing to the short stretch of the balustrade on landing E03 using the appropriate
fixture obtained when assembling elements A20, A03, C92 and B08 (fig. 11). On the handrail A02 clean the cut
and heat the end part, fix the caps A03 of the fixture obtained (after cleaning the cut and heating the end part of
the handrail A02) using the glue X01, fix in a permanent manner with screws C87 (fig. 11).
Final Assembly
47. To further stiffen the staircase at intermediate points, secure elements F09 to the wall and join them to the
balusters C03 using elements F08. Drill using a D. 8 mm -
B12 (fig. 13).
48. Glue the nosings H01 onto the treads L02 using element B96 (Fig. 1). If installing outdoors use acetic silicone.
49. Glue the step board H03 and H04 onto the landing E03 using element B96 (fig. 1) for use indoors, and acetic
silicone (not included) for use outdoors.
Maintenance
After assembly check the integrity of the staircase and touch up any damaged parts with a rust-proofing undercoat
(not provided) and a topcoat of varnish included in the supply.
To ensure a long life of the product, it is recommended to periodically perform the above operation.
In case of accidental damage to the varnishing, and in any case at least every 4 months, carry out the above
described operation.
Stairs installed in particularly aggressive environments (for example, near the sea, in industrial areas, etc.) must be
washed every month with fresh water and non-aggressive detergents, without using pressurized water.
/
7
") at the top with elements B54 and B55 after drilling it with a D. 5 mm -
8
/
" and H. 1130 mm - 44
3
4
After you have finished assembling the staircase,
please visit our website and send us your suggestions: www.arkestairs.com
/
") together with the element F07 after cutting it by 35 mm - ⅜".
7
8
/
") (using gloves). Fix it on the first column
7
8
/
"; for D. 140 cm - 55 ⅛" and D. 160 cm - 63" staircases two
1
8
/
"). Tighten elements C31 taking care that
1
2
/
" in the elements F01 (applying silicone, not included, to
13
16
/
" bit and use elements B36, B37, C29, B11 and
5
16
7 - EU
/
13
" bit in its
64
1
/
" staircase
4
/
" cutting it by
3
4
Publicidad
