Kohler Sterling 500 Serie Instrucciones De Instalación Y Cuidado

USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310 SterlingPlumbing.com
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Measure distance "A." Subtract 1/8" (3 mm)
1
from "A" and cut the bottom track.
A
Length =
A – 1/8" (3 mm)
1/8" (3 mm)
Position the wall jamb with the "groove" side up.
6
Drill a 3/16" hole 3" (76 mm) from each end and
one in the center between the two holes.
x2
3/16" Diameter Holes
Groove
3" (76 mm)
3" (76 mm)
1166704-2-C
Required Tools
100% Silicone Sealant
Tin Snips
32 Teeth Per Inch Blade
1/8", 3/16", 5/16", 5/16" Masonry
Miter Box Masking Tape
File the bottom track edges to fit curved corners
2
of the shower or bath unit.
Position the wall jambs over the bottom track.
7
Snip/file bottom edges for a snug fit.
Parts Identifi cation
1173290**
Hardware Skin Pack
1173259**
Towel Bar Bracket and Hardware
Top Track
Long Leg
Wall Jamb
172821
Bumper
1171026-01**
Bracket
1049018-G
Screw
# 8-18 x 3/8"
Towel Bar
Wall Jamb*
1077762
Anchor
Measure and mark the exact center of the bottom
3
track. Center the guide and mark the hole.
Plumb both wall jambs. Mark the screw holes.
8
x2
Large Leg
to Outside
1
Installation and Care Instructions
500, 660, 670, and 690 Series Sliding Shower and Bath Doors
*Call Customer Care Center to order replacement parts.
Series Number Label
1129847-01**
Top Track
172818
Roller
1042862-A
Screw
#8-32 x 3/8"
Towel Bar*
1042930-A
Screw
#6-32 x 5/16"
1083114**
Guide
Outside Panel*
1129841-01**
Bottom Track
Drill a 1/8" hole at the marked location and
4
attach the guide with a #6-32 x 5/16" flathead
screw.
#6-32 x 5/16"
Drill 5/16" holes and insert the anchors.
9
x2
3
2
1
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Long Leg
Wall Jamb*
1171024-01**
Handle
1129843-01
Tape
1048208-E
Screw
#8-18 x 1-1/4"
Inside Panel*
1129873
Cover
Center the bottom track on the ledge with the
5
leg to the outside. Tape in place and mark the
position.
To Outside
Secure both wall jambs with screws. Attach a
10
bumper to the top and bottom location.
Bumper
x2
#8-18 x 1-1/4"