TecMate Optimate lithium TM470 Modo De Empleo página 5

AUTOMATIC DIAGNOSTIC CHARGER FOR 12.8V LiFePO
PHOSPHATE ) BATTERIES FROM 2.5Ah TO 30Ah:
Input: 100-240V maximum 0,23A. The maximum output current is 0,8A.
SAFETY WARNING AND NOTES: IF YOU HAVE NOT YET DONE SO, READ
THE PRECEDING PAGES LABELLED "IMPORTANT SAFETY
INSTRUCTIONS" BEFORE OPERATING THIS CHARGER.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.
USING THE OPTIMATE LITHIUM 0.8A
CORRECT USE:
Use the charger only if the input and output leads and connectors are in good, undamaged condition. If the input cable is
damaged, it is essential to have it replaced without delay by the manufacturer, his authorised service agent or a qualified workshop, to avoid
danger. Protect your charger from damp and humid conditions both during use and in storage. Damage resulting from corrosion, oxidation or
internal electrical short-circuiting is not covered by warranty. Distance the charger from the battery during charging to avoid contamination
by or exposure to acid or acidic vapours. If using it in the horizontal orientation, place the charger on a hard, flat surface, but NOT on plastic,
textile or leather. Use the fixing holes provided in the enclosure base to attach the charger to any convenient, sound vertical surface.
EXPOSURE TO LIQUIDS
from above, or to light rainfall. Prolonged exposure to falling rain is inadvisable and longer service life will be obtained by minimizing such
exposure. Failure of the charger due to oxidation resulting from the eventual penetration of liquid into the electronic components, connectors
or plugs, is not covered by warranty.
VERY FLAT NEGLECTED BATTERIES:
for an extended period may develop permanent damage in one or more cells. Such batteries may heat up excessively during charging.
During the SAVE mode the program limits charge current if the voltage is below 12.8V and the program should detect obvious cell damage
and will automatically suspend charging, but the higher the cell count in parallel the more difficult it is to detect a bad cell e.g. a 5Ah battery
typically has 4 series connected sets of 2 parallel cells (4S2P configuration - total 8 cells), a 10Ah battery has 4 series connected sets of 4
parallel cells (4S4P configuration - total 16 cells).
ALWAYS monitor the battery temperature during the first hour, then hourly there-after. If at any time the battery is uncomfortably hot to
touch or you notice any unusual signs, DISCONNECT THE CHARGER IMMEDIATELY.
CHARGING TIME
Charge time on a flat but otherwise undamaged battery:
For batteries rated from 2.5Ah to 5Ah: 180 to 360 minutes to progress to the voltage retention test.
For batteries rated above 5Ah: 125% of the battery's Ah rating, so a 30Ah battery should take no more than about 38 hours to progress to
the voltage retention test.
Deep-discharged batteries may take significantly longer. A full charge may not be achieved within the 24 hour charge safety limit. In this
case follow the reset procedure below.
RESETTING THE CHARGE & TEST CYCLE
Disconnect from the AC mains. Wait for the POWER ON LED #1 to go out. Upon reconnection to AC power LEDs #3, 4, 5 and 6 will flash
twice to confirm micro processor health, irrespective if the charger remains connected to a battery or not.
ECO POWER SAVING MODE WHEN THE CHARGER IS CONNECTED TO AC SUPPLY:
The power converter switches to ECO mode when the charger is not connected to a battery resulting in a very low power draw of less than
0.5W (per charging bank), equivalent to power consumption of 0.012 kWh per day. When a battery is connected to the charger power
consumption depends on the current demand of the battery and its connected vehicle /
charged and the charger is in long term maintenance charge mode (to keep the battery at 100% charge) the total power consumption is
estimated to be 0.024 kWh or less per day.
:
This charger is designed to withstand exposure to liquids accidentally spilled or splashed onto the casing
Pay particularly close attention to the following A LiFePO
(LITHIUM IRON
4
battery left deep-discharged
4
electronic circuitry. After the battery has been
5