Recovery Tank; Detergent Solution Tank; Floor Cleaning; Connection Of The Batteries To The Machine - ADIATEK jade 55ct Uso Y Mantenimiento

GB
ATTENTION:
To carry out brushes assembly operations with the
electric supply on, may cause damages to hands.
ATTENTION:
Use only brushes supplied with the machine or the
ones indicated in the paragraph "RECOMMENDED
BRUSHES". The use of other brushes can compromise
security.

RECOVERY TANK

Check that the cover of the suction filter (1) is cor-
rectly secured, after rotating the levers (2) and that
the suction motor hose is correctly connected.
Verify also that the squeegee hose (4) is correctly in-
serted into the seats and that the exhaust hose plug
(5) placed in the front part of the machine, is closed.

DETERGENT SOLUTION TANK

The capacity of the detergent solution tank is indi-
cated in the technical data.
Open the screw plug (1) placed in the rear left part
of the machine and fill the detergent solution tank
with clean water at a maximum temperature of 50°C.
Add the liquid detergent in the percentage and con-
ditions foreseen by the manufacturer. To avoid ex-
cessive foam presence, which could cause problems
to the suction motor, use the minimum percentage
of detergent. Screw down the plug to close the tank.
ATTENTION:
Use always low foam detergent. To avoid foam pres-
ence, before starting working operation, introduce
into the recovery tank a minimum quantity of anti-
foam product.
Never use pure acid.

FLOOR CLEANING

CONNECTION OF THE BATTERIES TO THE MA-
CHINE
Plug in the batteries connector (1) to the machine
connector (2), placed in the rear part of the machine.

STARTING OF THE MACHINE

1. Turn the key (8) clockwise.
2. Check the battery type and the charge level on
the display (1).
3. Press the brushes motor switch (5).
4. Press the suction motor switch (6).
5. Press the solenoid valve switch (4).
6. Acting upon the brushes base lifting pedal (13)
lower the brushes base.
7. Acting upon the solution valve lever (11) open
and adjust the solution detergent flow.
The water starts to flow automatically acting upon
the levers drive control (9). On the instrument board
the indicator of the open solution valve (4) will turn
on. Releasing these levers, the flow will stop.
8. Acting upon the squeegee lifting lever (12) lower
the squeegee.
9. Acting upon the levers drive control (9) the ma-
chine starts to move, the brushes start to rotate and
the squeegee starts to dry.
10. During the first metres check that the squeegee
adjustment guarantees a perfect drying action and
that the detergent solution flow is appropriate. It
has to be sufficient to wet the floor. Always consider
that the correct quantity of solution detergent de-
pends on type of floor, dirtiness and machine speed.

FORWARD MOVEMENT

The traction of the machine is given through an
electronically controlled motor.
To move the machine, switch on the key (8) and then
rotate the levers drive control (9) placed on the han-
21
dle bar, in forward you obtain the forward drive, in
reverse the backwards movement is obtained. The
control acts in a progressive way, therefore it is pos-
sible to graduate the speed depending on each re-
quirement rotating the lever whatever it is necessary.
During reverse motion the speed is reduced.

SPEED ADJUSTMENT

Two values of the maximum drive working speed in
forward movement can be chosen.
Set the wanted speed through the speed selection
switch (14).
ATTENTION:
Moving the machine backwards, make sure that the
squeegee is lifted.

WORKING BRAKE

To stop the machine during normal working situa-
tion, it is sufficient to release the levers drive control
(9), as the machine is equipped with an electronic
braking system. The brushes and the detergent solu-
tion flow stop automatically.

EMERGENCY BRAKE

In case of an emergency, an immediate stop can be
obtained acting upon the lever of the emergency
and parking brake (10) by pushing it downwards.
ATTENTION:
This control blocks the machine immediately. The
emergency brake functions also as a parking brake.
To start again to work, release the lever by unblock-
ing the parking button on the lever itself and act
again upon the levers drive control (9).
GB